Zimmer Biomet Persona Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 72

Zimmer Biomet Persona Скачать руководство пользователя страница 27

25 |

Persona

®

Revision

Knee System

Surgical Technique

Thick Femoral

Depth Line

Optional Femoral Rotation or Size

Adjustment (4-in-1 Cut Guide)

If the primary knee resections need to be adjusted,
the femoral sizing/cut guide can be used to correct
the resection.

Note:

Assess bone loss to size the femur properly.

Sizing to the existing bone may result in undersizing
the femoral component. In this case, consider
upsizing the femoral component.

While attached to the straight or offset adapter, use
an oscillating saw to make the anterior, posterior,
anterior chamfer and posterior chamfer cuts

(Figure 60).

Note:

A narrow neck oscillating blade will provide

added clearance for the cuts.

Note:

Distal spacers can be used to compensate for

missing bone that would need to be replaced with
augments.

Optional Posterior Augment Resection

The 5 and 10 mm posterior augment cut slots are
available for augment preparation (Figure 60).

Note:

Posterior augments can also be cut using a

femoral provisional at a later stage in the surgical
procedure.

Femoral Stem Housing Preparation

Straight Stem Preparation Only

If the planned stem size has a diameter less than 16
mm, the bone must be cleared to accommodate the
femoral stem provisional. The 16 mm tilt reamer can
be used for this purpose. Drive the tilt reamer in the
femoral canal until the thick femoral line is level with
the distal femur (Figure 61).

Offset Stem Preparation Only

Use a tilt reamer to clear out bone for the offset
transition. Drive the tilt reamer in the femoral canal
until the thick femoral line is level with the distal femur.
Tilt the tilt reamer in the same direction as the arrow
on the offset stem reamer adapter to remove the
necessary amount of bone for a 3 mm or 6 mm offset
stem (Figure 62).

Figure 60

Figure 61

Figure 62

10 mm

5 mm

0 mm

«
...
25
26
27
28
29
...
»

Содержание Persona









































































Отзывы:

Нет отзывов