Zimmer Biomet Persona Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 72

Zimmer Biomet Persona Скачать руководство пользователя страница 32

30 |

Persona

®

Revision Knee System

Surgical Technique

Trial Reduction

(cont.)

TASP Removal

The entire TASP construct must be removed to
exchange the bottom in the TASP construct. To remove
or exchange the bottom, flex the knee greater than 30
degrees, push in the TASP posteriorly to disengage
anteriorly (1) and lift (2) the tibial sizing plate handle
while attached to the TASP construct (Figure 78).
Once the anterior lip of the TASP bottom is above the
anterior rail of the tibial baseplate provisional, rotate
the TASP out of the joint space medially or laterally (PS
TASP Top only) (Figure 79). This will aid in preventing
unwanted shim disassembly during TASP removal.

Note:

Varus/Valgus forces may make it difficult to

remove the TASP construct. To aid in the removal
of the TASP and prevent breakage, ensure the joint
is in a neutral position when removing the TASP
construct.

Figure 78

Figure 79

«
...
30
31
32
33
34
...
»

Содержание Persona









































































Отзывы:

Нет отзывов