Zetor Proxima HS 100 Скачать руководство пользователя

Страница: 46 / 212

Road and reduced speeds shifting lever

PTO selection control lever

Lever of shifting of speed 540 (or 540E) and 1,000 rpm of the rear output shaft

Lever of hand brake and hitch for single-axle trailer

Shifting is carried out with tractor in standstill.

H Road

gears

N Neutral
L Reduced

gears

G150

Shifting is made when the tractor stops.

a - Independent speed of PTO shaft - PTO shaft speed de-

pends upon the engine speed

n - Neutral
b - Ground speed of PTO shaft (through gearbox) - PTO

shaft speed depends upon the engaged gear speed

G154

Shifting can be carried out when the tractor is in standstill
by pulling up or pushing down the lever.

* The tractor can be equipped optionally by 6-, 8- or 21-
groove termination of the output shaft.

Shifting of 540 and 1,000 (or 540E) min

-1

possible regardless to the number of grooves on the

installed termination. Speed of the output shaft and

type of the termination shall be chosen depending on

the prescribed speed of the aggregated machine.

a - 1,000 min

-1

(or 540E min

-1

)

b - 540 min

-1

G153a

1. Hand brake lever.
2. Lever of the single-axle trailer hitch control.

When stopping or leaving the tractor you must

always secure the tractor with the parking brake.

The engagement of a gear does not prevent the

tractor from getting in motion (the clutch is

disengaged)!

If the tractor is standing on a slope, its wheel must be

additionally secured with wedges!

E155

ACQUAINTANCE WITH TRACTOR

Содержание Proxima HS 100





















































































































































































































Результаты поиска

Содержание Proxima HS 100

Отзывы:

Похожие инструкции для Proxima HS 100

Бренды по названию

Популярные бренды

Zetor Proxima HS 100, Руководство оператора

Результаты поиска

Содержание Proxima HS 100

Отзывы:

Похожие инструкции для Proxima HS 100

Бренды по названию

Популярные бренды