Zetor Proxima HS 100 Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 212

background image

Battery disconnector

Attention! When the engine is switched off, the control unit of the engine and of the exhaust

system remains active for about 2 minutes because of storage of the engine operation data and
drawing of urea back into the tank. During this time the supply of current from the accumulator must
not be interrupted. Do not disconnect the accumulator before this time expires.

Accumulator battery maintenance

F298

Keep the accumulator battery clean and properly fixed to the vehicle. However, the fixing device must not
deform the battery case. In the case of polypropylene batteries the electrolyte level must not be below the
minimum mark indicated on the case.

Only add distilled water to the battery!

1. When working with the battery first read the attached manual.
2. During work with the battery protect your eyes with goggles or a safety shield!
3. The electrolyte is a caustic substance; therefore, handle it with proper care.If your skin or clothes
get stained by electrolyte, wash the skin or clothes with water and neutralize them with soap.
4. During charging hydrogen is released from the electrolyte on the electrodes. Hydrogen mixed with
the air forms an explosive mixture. Therefore, it is prohibited to handle open fire near the battery
during charging.
5. An explosion may also be caused by a spark created on the disconnection or release of a terminal
when the charging circuit is on.
6. Keep the battery out of reach of children!
7. A discarded battery is dangerous waste for the environment - when buying a new battery hand the
old one over to the dealer, who will dispose of it free of charge.

Batterydisconnector is placed on the left side of the tractor
behind the stairs of the driver.
a - Batteryconnected
b - Batterydisconnected

When the tractor is at dead parking, disconnect

the battery by means of the battery disconnector (1). If
a tractor is dead parked for a longer period of time, it
is necessary to recharge at least once a month from
the reasons of self-discharge of battery.

FH12N022

ELECTRIC INSTALLATION

154

«
...
153
154
155
156
157
...
»

Содержание Proxima HS 100





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proxima HS 100

Бренд: K&M Страницы: 9

Бренд: MacDon Страницы: 2

Бренд: Nakayama Страницы: 24

Бренд: Dynapac Страницы: 34

Бренд: Yanmar Страницы: 202

Бренд: Still Страницы: 246

Бренд: GOLDONI Страницы: 160

Бренд: MTD Страницы: 20

Бренд: Broan Страницы: 32

Бренд: Ignite Страницы: 32

Бренд: Komatsu Страницы: 6

Бренд: Broan Страницы: 10

Бренд: J&M Страницы: 31

TRAC-LIFT T50HLSS

Бренд: JAWA Страницы: 11

Бренд: Zetor Страницы: 197

FORTERRA HSX 100

Бренд: Zetor Страницы: 250

HORTUS CL Series

Бренд: Zetor Страницы: 142

Бренд: Zetor Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды