Zetor Proxima HS 100 Скачать руководство пользователя страница 111

Страница: 111 / 212

Switching on the rear PTO shaft - independent revolutions

PP15N020

Number of PTO shaft revolutions depends on the number of engine revolution.

When the tractor is not going with its engine running:

A - move the gear shift lever of dependent and independent engine speed to the upper position to gear

independent revolutions of the rear PTO shaft
B - use the gear shift lever to select suitable speed of the rear PTO shaft

C - by pressing the switch of the rear PTO shaft (1), the rear PTO shaft is activated.

Activation of the rear PTO shaft is indicated by displaying the number of revolutions of the rear PTO shaft on

the instrument panel display.

If the aggregated machine permits, engage the rear PTO shaft with min. engine revolutions of

1,500 rpm.

Switching on the rear PTO shaft - dependent revolutions

PP15N019

Number and sense of revolutions depends on the shifted gear and position of the reversion lever. In the

mode dependent revolutions, there is no influence of the position of the reduction lever on the number of

revolutions of the rear PTO.

When the tractor is not going with its engine running:
A - move the gear shift lever of dependent and independent engine speed to the lower position to gear

dependent revolutions of the rear PTO shaft

B - use the gear shift lever to select suitable speed of the rear PTO shaft

C - when the clutch pedal is pushed down, use the main gear shift to shift a gear and the reversion level to

select the driving direction. When the tractor starts driving, the rear PTO shaft starts to rotate as well.

Use the clutch pedal for short-term interruption of torque transmission from the rear PTO

shaft. The switch of the rear PTO shaft is not functional in this mode.

PTO DRIVE OF AGRICULTURAL MACHINES

110

Содержание Proxima HS 100





















































































































































































































Результаты поиска

Содержание Proxima HS 100

Отзывы:

Похожие инструкции для Proxima HS 100

Бренды по названию

Популярные бренды

Zetor Proxima HS 100, Руководство оператора

Результаты поиска

Содержание Proxima HS 100

Отзывы:

Похожие инструкции для Proxima HS 100

Бренды по названию

Популярные бренды