Zetor Proxima HS 100 Скачать руководство пользователя | Manualshive

Страница: 34 / 212

background image

Tilt steering wheel

Tilting and protrusion of steering wheel

When the steering wheel is adjusted, fold the locking lever (2) to the instrument panel and the

locking lever (1) so that it is directed parallel to the axis of the steering wheel column. After slight
pulling of the locking levers in the direction from the steering wheel column, the levers can be set to

any position.

Adjusting the angle of the wheel
The angle can be adjusted by tilting the wheel after it is
unlocked by moving the lever (1) in the direction shown by
the arrow.
After adjusting, lock the wheel by pressing the lever (1) in
the opposite direction than shown by the arrow.

W1

Tilting column of steering wheel enables variable setting of
position of the steering wheel both in terms of angle and
height.

Height setting of steering wheel
The setting is done by protrusion or retracting the steering
wheel after unlocking arrestment by turning a lever (1) in
the direction of an arrow. After setting the steering wheel,
lock the lever (1) by tightening in the direction of an arrow.

Angle setting of steering wheel
Setting is done by tilting the steering wheel after unlocking
the lock by turning the lever (2) in the direction of the
arrow. After setting the steering wheel, secure the lever
(2) by retightening against the direction of the arrow.

F205

ACQUAINTANCE WITH TRACTOR

33

«
...
32
33
34
35
36
...
»

Содержание Proxima HS 100





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proxima HS 100

Бренд: imants Страницы: 52

Бренд: Ventrac Страницы: 53

Бренд: Ventrac Страницы: 69

Бренд: Ventrac Страницы: 72

Бренд: jcb Страницы: 21

Бренд: CAMSO Страницы: 106

Бренд: Allis-Chalmers Страницы: 45

CRAFTSMAN 944.604001

Бренд: Sears Страницы: 56

E15TC75HPS - Fully Integrated Trash Compactor

Бренд: Electrolux Страницы: 2

Бренд: Jodale Perry Corporation Страницы: 12

Бренд: Thwaites Страницы: 24

Бренд: McGill Страницы: 30

Бренд: Digga Страницы: 16

Бренд: Ariens Страницы: 36

Бренд: Ariens Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды