manualshive.com logo in svg

Zetor Proxima HS 100, Руководство оператора

Операторская инструкция "Zetor Proxima HS 100" - это необходимый ресурс для правильной эксплуатации вашей техники. Скачайте бесплатно этот руководство с нашего сайта manualshive.com и ознакомьтесь с основными функциями и рекомендациями по обслуживанию вашего трактора.

Поделиться
Скачать
background image

Weights of the front three-point hitch ........................................................................................................ 149 
Weights of rear wheels .............................................................................................................................. 149 
Valve for filling tyre tubes with liquid ......................................................................................................... 149 
Chocking of front wheels ........................................................................................................................... 150 
Procedure of filling the tyres with liquid ..................................................................................................... 150 
Procedure of draining liquid from the tyres ................................................................................................ 151 
Antifreeze solution for tyre filling................................................................................................................ 151 

Electric installation ....................................................................................................................................... 153 

Basic service information ........................................................................................................................... 153 
Accumulator battery ................................................................................................................................... 153 
Battery disconnector .................................................................................................................................. 154 
Accumulator battery maintenance ............................................................................................................. 154 
Alternator ................................................................................................................................................... 155 
Alternator maintenance ............................................................................................................................. 155 
Electric installation overload  ..................................................................................................................... 155 
Fuse panel ................................................................................................................................................. 156 
Checking the adjustment of the front grill headlights ................................................................................ 158 
Adjusting the front grill headlights ............................................................................................................. 158 
Checking the adjustment of the cab roof headlights ................................................................................. 159 
List of lamps............................................................................................................................................... 159 

Tractor maintenance .................................................................................................................................... 161 

Service inspections .................................................................................................................................... 161 
Steps performed daily before the start of work .......................................................................................... 161 
Steps performed every 50 hours of work .................................................................................................. 161 
Steps performed every 100 hours of work ................................................................................................ 161 
Steps performed every 500 hours of work ................................................................................................ 161 
Steps performed outside the interval of 500 hours of work ....................................................................... 162 
Monthly performed actions ........................................................................................................................ 162 
Filling and filter replacement ...................................................................................................................... 163 
Fuels, coolants and lubricants used - amounts ......................................................................................... 164 
ZETOR service fillings ............................................................................................................................... 164 
Motor oils ................................................................................................................................................... 164 
Oil in the gearbox and final drivehousing .................................................................................................. 164 
Oil in the rear axle gantries ........................................................................................................................ 164 
Oil for the front driving axle ........................................................................................................................ 164 
Oil for the hydrostatic steering of the tractors ............................................................................................ 164 
Specification of oils for Zetor engines equipped by diesel particle filter .................................................... 164 
Specification of the oil for the gearbox housing and the final drive housing ............................................. 164 
Specification of the oil for the portals ........................................................................................................ 165 
Specification of oil for the front driving axle ............................................................................................... 165 
Specification of oil for the tractor hydrostatic control system .................................................................... 165 
Other recommended service fillings tested on Zetor tractors .................................................................... 165 
Oils for Zetor engines which are equipped with diesel particle filter ......................................................... 165 
Oil in the gearbox and final drivehousing .................................................................................................. 165 
Oil in the rear axle gantries ........................................................................................................................ 166 
Oil for the front driving axle ........................................................................................................................ 166 
Oil for the hydrostatic steering of the tractors ............................................................................................ 167 
Front PTO oil ............................................................................................................................................. 167 
Plastic lubricant for the tractor ................................................................................................................... 167 
Hydraulic brake liquid for the tractors ........................................................................................................ 168 
Liquid for the cooling system of the tractors .............................................................................................. 168 
Fuel for Zetor engines which are equipped with diesel paricle filter .......................................................... 168 
Urea (urea solution AUS 32) ..................................................................................................................... 168 
Tractor greasing plan ................................................................................................................................. 169 
Safety instructions for lubrication of the tractor ......................................................................................... 169 
Solid front drive axle .................................................................................................................................. 169 
Hitch for a single-axle semi-trailer ............................................................................................................. 169 
Front three-point hitch ............................................................................................................................... 169 
Three-point hitch ........................................................................................................................................ 170 
Hitch mouth for a trailer ............................................................................................................................. 170 
Upper linkage bracket ................................................................................................................................ 170 
Technical maintenance of the tractors after a general overhaul of the main groups  ............................... 170 

Maintenance instructions ............................................................................................................................ 171 

CONTENTS

8

Содержание Proxima HS 100





















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proxima HS 100

Hitachi BEKA-MAX Installation Instruction preview
BEKA-MAX
Бренд: Hitachi Страницы: 58
CAMSO 100-3613 Operation And Maintenance Manual preview
100-3613
Бренд: CAMSO Страницы: 24
Winton WTL Series Owner'S Manual preview
WTL Series
Бренд: Winton Страницы: 20
Warn 85690 Installation Instructions Manual preview
85690
Бренд: Warn Страницы: 15
Hagie UpFront 120 Operator'S Manual preview
UpFront 120
Бренд: Hagie Страницы: 67
jcb Fastrac 3170 Service Manual preview
Fastrac 3170
Бренд: jcb Страницы: 21
Jenn-Air TC507B1 Use & Care Manual preview
TC507B1
Бренд: Jenn-Air Страницы: 28
Allis-Chalmers G Service Manual preview
G
Бренд: Allis-Chalmers Страницы: 45
Cub Cadet YANMAR EX2900 Specifications preview
YANMAR EX2900
Бренд: Cub Cadet Страницы: 2
Cub Cadet 2176 Operator'S Manual preview
2176
Бренд: Cub Cadet Страницы: 60
Classic Accessories Zero Turn 73997 Instructions preview
Zero Turn 73997
Бренд: Classic Accessories Страницы: 3
Belarus 920.4 Operating Manual preview
920.4
Бренд: Belarus Страницы: 58
Belarus 80.1 Series Operation And Service Manual preview
80.1 Series
Бренд: Belarus Страницы: 143
Belarus 3522.5 Operator'S Manual preview
3522.5
Бренд: Belarus Страницы: 340
AGI WHEATHEART X130 Operator And Assembly Manual preview
WHEATHEART X130
Бренд: AGI Страницы: 46
Ariens 96046000100 Repair Parts Manual preview
96046000100
Бренд: Ariens Страницы: 36
Ariens A21A42 Operator'S Manual preview
A21A42
Бренд: Ariens Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды