Zepter AqueenaPro WT-100 Скачать руководство пользователя

Страница: 14 / 64

AqueenaPro WT-100

Installation and Repair manual

Rev. A

Installation and Repair Manual AqueenaPro WT-100

Page 14 of 64

7. Product installation

Note!

1. The AquuenaPro is a water filtration system for home use. Any use outside the indoor home environment

and for purpose other than purifying water for household use will automatically void your warranty.

The AqueenaPro should not be used on feed water that is microbiologically unsafe or unknown

microbiological quality without disinfecting the water before using the device.

Cold water plumbing – AqueenaPro must be connected to cold water pipe. If the hot water (>38°C) as

water source will be used, it will cause permanent damages to RO membrane and severely degrades the

product

Plumbing and carpentering work is needed.

Ensure, whether the main water supply is turned off before any plumbing work is stared!

7.1. Pre-Installation Preparations

To secure correct functionality and to keep long life time of the water purifier AqueenaPro, the place for the main

unit should be consider and precisely chosen in prior, following recommendation should be followed:

7.1.1. Recommended side preparation

Mains connection not more than 1.5 m from the point of installation of AqueenaPro

Water supply not more than 3 m away

Drain for rejected water not more than 3 m away

Space as per dimensions of the AqueenaPro

It is preferable to install the AqueenaPro near a sink so that inlet and reject water lines are easily available.

Avoid sharp bends in the pipe. Do not bend or block the rejected water tube.

Do not confine the AqueenaPro in a tight cabinet.

Содержание AqueenaPro WT-100

































































Результаты поиска

Содержание AqueenaPro WT-100

Отзывы:

Похожие инструкции для AqueenaPro WT-100

Бренды по названию

Популярные бренды

Zepter AqueenaPro WT-100, Руководство по установке и ремонту

Результаты поиска

Содержание AqueenaPro WT-100

Отзывы:

Похожие инструкции для AqueenaPro WT-100

Бренды по названию

Популярные бренды