Zepro ZT MK2 Скачать руководство пользователя страница 46

Страница: 46 / 52

ZT MK2

Marking

www.zepro.com

10.5.1 Autotilt additional sticker

There is an additional sticker affixed next to the control device sticker on tail lifts fitted with autotilt.

The stickers are available in standard versions and in a latterally reversed version (option) for affixing on the

opposite side of the vehicle.

Affix additional autotilt stickers for CD3 and CD9 next to their respective controller stickers and align them

and with the two middle symbols for the tilt down and tilt up functions.

Additional autotilt sticker for CD 19

2021-06-01 78877TL

www.hiab.com

Additional autotilt sticker for CD 9

www.hiab.com
77663TL 2020-02-10

www.hiab.com
55053TL 2020-03-04

www.hiab.com
78888TL 2021-06-11

www.hiab.com
55057TL 2020-03-04

Additional autotilt sticker for CD 3

Affix the additional CD19 autotilt sticker on control device CD19 directly below the line in the right column of

symbols and in line with the symbols above.

Control device

Sticker

(standard)

Sticker (latter-

ally reversed)

CD 3

78888TL

78889TL

CD 9

77663TL

78344TL

CD 19

78878TL

78892TL

Содержание ZT MK2





















































Результаты поиска

Содержание ZT MK2

Отзывы:

Похожие инструкции для ZT MK2

Бренды по названию

Популярные бренды

Zepro ZT MK2, Руководство по установке

Результаты поиска

Содержание ZT MK2

Отзывы:

Похожие инструкции для ZT MK2

Бренды по названию

Популярные бренды