Zepro ZT MK2 Скачать руководство пользователя страница 6

Страница: 6 / 52

ZT MK2

Important information

www.zepro.com

1.4

CE marking

ZEPRO tail lifts for sale on the European market are CE marked (Conformité Européenne). The manufacturer

guarantees that the product complies with the EU Machinery Directive.

Follow the installation instructions carefully. Modifications not approved in writing by the manufacturer are

not permitted. Welding is not permitted.

1.5

Product approval

Properly assembled, this product meets relevant requirements according to EN 1756-1:2001 + A1:2008.

1.6

Hydraulic oil

If the hydraulic oil needs to be replenished, only the oil recommended by ZEPRO is permitted to be used.

Hydraulic systems with hydraulic oil tanks without labelling are only permitted to be filled with highly refined

mineral oil (art. no. 21963, 1 litre).

Hydraulic systems with hydraulic oil tanks marked with a specification for the hydraulic oil are only permitted

to be filled with the oil specified on the label.

1.7

Guarantee

After installation, testing and verification, the tail lift’s delivery card must be registered for the guarantee to be valid.

Содержание ZT MK2





















































Результаты поиска

Содержание ZT MK2

Отзывы:

Похожие инструкции для ZT MK2

Бренды по названию

Популярные бренды

Zepro ZT MK2, Руководство по установке

Результаты поиска

Содержание ZT MK2

Отзывы:

Похожие инструкции для ZT MK2

Бренды по названию

Популярные бренды