background image

ZT MK2

48

Testing and verification

www.zepro.com

Picture 71. 

Testing and verification

Max 2º

Max. 15 mm

B

D

C

A

B

D

C

A

11 

Testing and verification

Testing and verification of the tail lift takes place in accordance with the installation/delivery inspection. 

Verify that the tail lift is suitable for the vehicle in question and for the intended use.

11.1  Static load test

11.1.1  Deformation

Position the tail lift half way up to the vehicle floor level and with the platform in the horizontal position. 

Measure dimensions A-B-C-D for comparison as illustrated.
Place a test load on the platform according to the table (for the respective tail lift model/lifting capacity).

Remove the test load from the platform. Repeat the measurement of A-B-C-D and verify that there has been 

no deformation of the lift or its fixing.

11.1.2  Drift

Place a test load on the platform according to the table. The tail lift must be at the same level and angle as 

the vehicle floor. Leave the test load for 15 minutes. Verify that the platform drift is no more than 15 mm on 

the vertical (points A and D) and 2º in terms of the angle.

Capacity

Load 1000 kg

Load 1500 kg

Distance on platform (L)

1500 kg

1410 mm

940 mm

2000 kg

1875 mm

1250 mm

2500 kg

2360 mm

1570 mm

Static load (Test load 1.25 x tail lift loading capacity).

For tail lifts with load centre of 750 mm

Vehicle floor le

vel

Deformation

Operation

Содержание ZT MK2





















































Отзывы: