manualshive.com logo in svg

York YCAZ33BA3, Руководство пользователя, Страница: 30 / 88

Поделиться
Скачать
York YCAZ33BA3 Скачать руководство пользователя страница 30

YORK INTERNATIONAL

30

The DAILY SCHEDULE SHUTDOWN message indi-

cates that the schedule programmed into the “CLOCK”

“SET SCHEDULE/HOLIDAY” is keeping the chiller from

running.

Run Permissive is an indicator that an external cycling

contact (i.e. flow switch) connected to terminals 13 and

14 is open, or a system switch(es) on the Microproces-

sor Board is in the OFF position. Whenever the con-

tact is open or a switch is OFF, the NO RUN PERM will

be displayed.

This message informs the operator that the chilled liq-

uid temperature is below the point (determined by the

setpoint and control range) that the micro will bring the

lead system on, or that the micro has not loaded the

system far enough into the loading sequence to be

ready to bring the lag system ON. The lag system will

GENERAL

Pressing the STATUS key will enable the operator to

determine current chiller operating status as a whole

and as individual systems. The messages displayed

will include running status, cooling demand, fault sta-

tus, external cycling device status, and anti-recycle

timer status. The display will be a single message re-

lating to the highest priority message as determined

by the micro. Status messages fall into the categories

of General and Fault Status with each of the catego-

ries discussed below.

GENERAL STATUS MESSAGE

Each of the general status messages with a descrip-

tion of its meaning will follow. In the case of messages

which apply to individual systems, SYS 1 and SYS 2

messages will both be displayed and may be different.

“X”’s in the sample displays indicate numerical values

will appear in actual displays.

This message informs the operator that the “UNIT”

switch on the Control Panel is in the OFF position which

will not allow the chiller to run.

26572A(D)

“STATUS” KEY

“STATUS”

KEY

U N I T

S W I T C H

I S

I N

T H E

O F F

P O S I T I O N

D A I L Y

S C H E D U L E

S H U T D O W N

S Y S # 1

N O

R U N

P E R M

S Y S # 2

N O

R U N

P E R M

S Y S # 1

N O

C O O L

L O A D

S Y S # 2

N O

C O O L

L O A D

Содержание YCAZ33BA3

























































































Отзывы:

Нет отзывов