York YCAZ33BA3 Скачать руководство пользователя страница 16

Страница: 16 / 88

YORK INTERNATIONAL

WIRING DIAGRAM

LD01989

LD01990

NOTES:

1. Field wiring to be in accordance with the current edition of the

National Electrical Code as well as all other applicable codes

and specifications.

2. Numbers along the right side of a diagram are line identification

numbers. The numbers at each line indicate the line number lo-

cation of relay contacts. An underlined contact location signifies

a normally closed contact. Numbers adjacent to circuit lines are

the circuit identification numbers.

3. Any customer supplied contacts must be suitable for switching

24VDC. (Gold contacts recommended). Wiring shall not be run

in the same conduit with any line voltage wiring

4. To cycle unit on and off automatically with contact shown, install

a cycling device in series with the flow switch (FLSW). See Note

3 for contact rating and wiring specifications.

5. To stop unit (Emergency Stop) with contacts other than those

shown, install the stop contact between 5 and 1. If a stop device

is not installed, a jumper must be connected between terminals

5 and 1. Device must have a minimum contact rating of 100VA at

115 volts A.C.

6. Alarm contacts are for annunciating alarm/unit malfunction con-

tacts are rated at 115V, 100VA, resistive load only, and must be

suppressed at load by user.

7. See application guide when optional equipment is used.
8. Contactors 1M and 3M are supplied only on part winding start

units. Compressor terminals 1, 2, 3 are connected to terminals

7, 8, 9 in compressor terminal box on across the line start units

and wires 100 thnu 102 and 200 thnu 202 are not supplied.

9. Control panel to be securely connected to earth ground.

FIG. 5

ELEMENTARY DIAGRAM

Содержание YCAZ33BA3

























































































Результаты поиска

Содержание YCAZ33BA3

Отзывы:

York YCAZ33BA3, Руководство пользователя, Страница: 16 / 88

Результаты поиска

Содержание YCAZ33BA3

Отзывы: