York YCAG18 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 100

background image

YORK INTERNATIONAL

85

FORM 150.40-NM25

SINGLE CIRCUIT UNITS

ANNUNCIATION ALARM

An optional Annunciation Alarm Kit p/n 025-28396-101
can be supplied which contains a second relay output
board whose dry contacts will transition to function as a
warning if a fault (“F” Code on displays) occurs or power
is lost to the control panel. The system has a set of dry
contacts which are normally open (N.O.) and close when
control power is applied to the panel. Anytime control
power is lost or a fault occurs, the contact will open,

0°F LOW AMBIENT ACCESSORY

GENERAL

The standard chiller is designed to operate in an ambi-
ent temperature of 35°F (1.7°C) or higher. If it is neces-
sary to operate the chiller in an ambient between 0°F
(–17.8°C) and 35°F (1.7°C), the chiller should be pur-
chased with the factory installed Low Ambient Kit.

OPERATION

The fundamental purpose of the Low Ambient Kit is to
reduce the capacity of the condenser when the ambient
temperature is in the 0°F to 35°F range. This assures
that adequate discharge pressures can be maintained
at low temperatures eliminating low suction pressure
faults. This is accomplished in three ways as follows:

1. The normally open solenoid valve in the condenser

liquid line is energized to stop flow in one half of the

condenser, that is, one “V” bank in the condenser.
NOTE: The valve has an orifice which has been sized
to prevent liquid build-up in the inactive portion of the
condenser.

2. Louvered panels are installed to reduce flow of air

over the inactive side of the condenser to aid in pre-
venting liquid build-up.

3. Below 45°F (7.2°C) fans are cycled by discharge pres-

sure only.

COMPONENTS

When the Low Ambient Kit is installed, the following
physical changes are made to the standard chiller:

1. One normally open solenoid valve is added to the

condenser circuit liquid line.

FIG. 60 – ANNUNCIATION ALARM WIRING

breaking the alarm circuit. A 28VDC or 120VAC exter-
nal alarm circuit (by others) must be wired into the YORK
supplied alarm contact. If the alarm circuit is applied to
chillers used for critical duty (such as process duty, or
cooling other critical equipment) and the alarm circuit
should fail to function, YORK will not be liable for dam-
ages.

The kit contains a N.C. Contact wired into TB4 termi-
nals 300 and 301 (See Fig. 60).

00019TG(R)

ALARM IS WIRED TO TB5

300

&

301

FROM DRY CONTACTS (OPEN ON ALARM)
CONTACT RATING 28VDC, 120VAC
AT 1A. A SURGE PROTECTOR
(SUPPRESSOR) YORK P/N 031-00808
MUST BE WIRED IN PARALLEL WITH AN
INDUCTIVE ALARM DEVICE (I.E. RELAY
COIL) AND MUST BE PHYSICALLY
LOCATED AT THE COIL.

«
...
83
84
85
86
87
...
»

Содержание YCAG18





































































































Отзывы:

Нет отзывов

Похожие инструкции для YCAG18

Бренд: Daikin Страницы: 48

Бренд: Poulan Pro Страницы: 24

Бренд: Pattfield Ergo Tools Страницы: 68

Бренд: Nakayama Страницы: 56

Бренд: Troy-Bilt Страницы: 20

Бренд: Troy-Bilt Страницы: 36

Бренд: HP Страницы: 14

Бренд: Hansa Страницы: 42

Бренд: Stiga Страницы: 85

Бренд: Alpina Страницы: 100

Бренд: Aqua One Страницы: 6

Бренд: Perlick Страницы: 7

Бренд: Cub Cadet Страницы: 15

Бренд: Cub Cadet Страницы: 20

PortaChill PC-05

Бренд: Tropicool Страницы: 3

Бренд: Wallenstein Страницы: 72

Бренд: Makita Страницы: 96

Бренд: Land Pride Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды