York YCAG18 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 100

background image

24

YORK INTERNATIONAL

SINGLE CIRCUIT UNITS

Closure slightly longer than 21 seconds will be treated
as 21 seconds.

The contact closure corresponds to a positive offset (rise)
from the setpoint on the panel. 1 sec. = +0 offset and 21
sec. = +40°F (4.4°C) or offset = 2 (time closed - 1 sec.).
For example: A setpoint of 25°F (–3.9°C) on the panel
and a contact closure of 8.5 sec. will result in an offset
of 15°F (8.33°C). This raises the RWT setpoint to 40°F
(4.4°C). Note: Metric Offset = 1.11 (time closed - 1 sec.).

To maintain the remote setpoint above the EMS Pulse
Width Modulation input (terminals 75 & 76) on the Digi-
tal Input Board must be refreshed every 30 minutes or
less (20 minutes is recommended). In otherwords, to
maintain the 40°F (4.4°C) RWT setpoint, the contacts
between terminals 75 & 76 must be closed for a period
of 8.5 seconds every 20 minutes. If this is not refreshed

SYSTEM “ON/OFF” SWITCH

This switch allows the operator to manually turn the unit
on or off. To operate the unit, the switch must be in the
“ON” position.

FIG. 15 – START/STOP CONTROLS

UNIT START-UP SEQUENCE

A simplified start-up sequence is provided on the con-
trol panel to aid the operator in running the chiller.

START/STOP CONTROLS

Before attempting start-up, the temperature and Start/Stop Controls should be properly set and understood.

at least every 30 minutes, the Micro Logic Board will
take this as a signal to change the RWT setpoint back
to the original setpoint of 25°F (–3.9°C) on the Control
Panel. See EMS/BAS Option in OPTIONS section for
more information.

ANNUNCIATION ALARM CONTACTS (OPTIONAL)

YORK can supply an alarm kit whose contacts will tran-
sition to function as a warning if unit malfunction occurs.
A 115VAC or 28VDC volt external alarm circuit (by oth-
ers) must be wired into the YORK supplied alarm cir-
cuit. If the alarm circuit is applied to chillers used for
critical duty (such as process duty, or cooling other criti-
cal equipment) and the alarm circuit should fail to func-
tion, YORK will not be liable for damages. See ALARM
Option in “OPTIONS” section for more information.

LD01854

«
...
22
23
24
25
26
...
»

Содержание YCAG18





































































































Отзывы:

Нет отзывов

Похожие инструкции для YCAG18

YCIV 0590-1500 50Hz

Бренд: York Страницы: 12

2- Cycle Gas Cultivator

Бренд: Yard Machines Страницы: 44

Бренд: Conair Страницы: 94

Бренд: Cobra Страницы: 11

Бренд: EarthWise Страницы: 42

Бренд: Talon Tools Страницы: 3

Бренд: Robur Страницы: 96

Бренд: AVANT Страницы: 22

Бренд: Gardena Страницы: 9

Бренд: Garland Страницы: 96

Бренд: Randell Страницы: 34

Бренд: Feider Machines Страницы: 23

Бренд: Hyundai Страницы: 69

Бренд: Daikin Страницы: 20

Бренд: Echo Страницы: 23

Бренд: Ruris Страницы: 179

Бренд: Trane Страницы: 60

Бренд: Tracmaster Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды