York YCAG18 Скачать руководство пользователя страница 76

Страница: 76 / 100

YORK INTERNATIONAL

PROBLEM

CAUSE

SOLUTION

F3 or F7 Fault Code

1. Improper Suction Pressure Cutout

1. Adjust as necessary & restart unit.

Faults on Low Pressure

Adjustment

2. Low Refrig. Charge

2. Repair Leak/Add Refrig.

3. Fouled Filter Drier

3. Change Drier Core

4. Thermal Expansion Valve Adjustment/

4. Adjust Compressor Suction Superheat

Failure

to 11°F (6.1°C) or Replace Power
Element (or Valve)

5. Reduced Flow of Chilled

5. Check GPM (See OPERATING LIMI-

Liquid through Cooler

TATIONS, page 3) Check operation of
pump. Clean Pump Strainer, Purge
Chilled Liquid System of air

6. Check LP Cutout Point on Panel

6. See manual for adjustment procedure

7. Defective Suction Press. Transducer

7. Replace Transducer

8. Fouled Compressor Suction Strainer

8. Remove & Clean Strainer

9. LLSV not opening

9. Check Wiring & LLSV

10. Faulty wiring to Transducer

10. Check wiring

11. Defective Relay Output Board

11. Replace Relay Output Board (Contact

the local YORK service representative.)

12. Defective Combo Board

12. Replace Combo Board (Contact

the local YORK service representative.)

13. Defective Micro Board

13. Replace Micro Board (Contact the

local YORK service representative.)

F4 or F8 Fault Code

1. Condenser fans not operating

1. Check Fans, Fuses, and Contactors.

Cuts out on High Dis-

or rotating backwards.

Air flow must be “UP”.

charge Pressure as

2. Too much Refrigerant

2. Remove Refrigerant

sensed by Micro-Proces-

3. Air in Refrigerant System

3. Evacuate and recharge

sor via high discharge

4. Defective Discharge Press. Transducer

4. Replace Discharge Press. Transducer

pressure transducer.

5. Defective Relay Output Board

5. Replace Relay Output Board (Contact

NOTE: If external H.P.

the local YORK service representative.)

Cut-out Switch trips

6. Defective Combo Board

6. Replace Combo Board (Contact

the Fault Code will be

the local YORK service representative.)

an F1 or F5.

F9 Fault Code

1. Temperature sensed incorrectly

1. Verify actual ambient temperature

Cuts out on high ambient

by thermistor

at probe

temperature. (Max. =

2. Fans Rotating Backwards

2. Air flow must be up. Correct fan

130°F (54.4°C).

rotation.

Will re-start automa-

3. Air flow to unit restricted (or

3. Check installation clearances. (See

tically if temperature

being re-circulated).

page 5.)

drops below
130°F (54.5°C)

F10 Fault Code

1. Temperature of Outside Air is

1. No problem exists.

Cuts out on Low Ambient

below cut-out setting.

Temperature 35°F (1.7°C)

2. Temperature sensed incorrectly

2. Verify actual ambient temperature

min. for Std. Unit. 0°F

by thermistor.

immediately at probe with thermometer.

(–17.8°C) min. for Low

3. Check Low Ambient Temp. Cut-out

3. Adjust if necessary.

Ambient Unit.)

setting on the display (Display Code 7)

NOTE: Operation below
35°F (1.7°C) requires
Low Ambient Accessory.

DUAL CIRCUIT UNITS

Содержание YCAG18





































































































Результаты поиска

Содержание YCAG18

Отзывы:

Похожие инструкции для YCAG18

Бренды по названию

Популярные бренды

York YCAG18, Руководство пользователя

Результаты поиска

Содержание YCAG18

Отзывы:

Похожие инструкции для YCAG18

Бренды по названию

Популярные бренды