York MILLENNIUM YCAR0315 Скачать руководство пользователя | Manualshive

Страница: 98 / 160

background image

98

YORK INTERNATIONAL

FORM 150.52-NM2 (1001)

System Start-Up

SYSTEM STARTUP CHECKLIST

In actual operation, due to splashing,
an oil level may be seen in both
sightglasses. Run the compressor for
a few minutes, shut the system down,
and assure there is an oil level show-
ing above the midpoint of the bottom
sightglass, but not above the top
sightglass with the compressor off.

If it is necessary to add oil, connect a YORK oil
pump to the oil charging valve on the compres-
sor, but do not tighten the flare nut on the delivery
tubing. With the bottom (suction end) of the pump
submerged in oil to avoid entrance of air, operate
the pump until oil drips from the flare nut joint,
allowing the air to be expelled, and tighten the
flare nut. Open the compressor oil charging valve
and pump in oil until it reaches the proper level as
described above. Be sure to use the correct
type of YORK oil for the refrigerant type.

q

6. Assure water pumps are on. Check and adjust

water pump flow rate and pressure drop across
the cooler.

Excessive flow may cause catastrophic
damage to the evaporator.

q

7. Check the control panel to assure it is free of

foreign material (wires, metal chips, etc.).

q

8. Visually inspect wiring (power and control). Wir-

ing MUST meet N.E.C. and local codes. See Fig.
8, page 36.

q

9. Check tightness of power wiring inside the power

panel on both sides of the motor contactors and
inside the motor terminal boxes.

q

10. Check for proper size fuses in main and control circuits.

q

11. Verify that field wiring matches the 3-phase power

requirements of the compressor. See chiller
nameplate (Page 25).

q

12. Assure 115VAC Control Power to TB1 has 20A

minimum capacity. See Fig. 8, page 36.

q

13. Be certain all water temp sensors are inserted

completely in their respective wells and are
coated with heat conductive compound. DO NOT
fill wells with water.

q

14. Assure that evaporator TXV bulbs are strapped

onto the suction lines at 4 or 8 o’clock positions.

JOB NAME: ______________________________

SALES ORDER #: _________________________

LOCATION: _______________________________

SOLD BY: ________________________________

INSTALLING
CONTRACTOR: ___________________________

START-UP
TECHNICIAN/
COMPANY: _______________________________

START-UP DATE : _________________________

CHILLER MODEL #: _______________________

SERIAL #: ________________________________

COMPRESSOR #1

MODEL#: ________________________________

SERIAL #: ________________________________

COMPRESSOR #2

MODEL#: ________________________________

SERIAL #: ________________________________

COMPRESSOR #3

MODEL#: ________________________________

SERIAL #: ________________________________

COMPRESSOR #4

MODEL#: ________________________________

SERIAL #: ________________________________

CHECKING THE SYSTEM 24 HOURS
PRIOR TO INITIAL START (No Power)
UNIT CHECKS

q

1. Inspect the unit for shipping or installation

damage.

q

2. Assure that all piping has been completed.

q

3. Check that the unit is properly charged and that

there are no piping leaks.

q

4. Open each compressor suction service valve, dis-

charge service valve, economizer service valve,
liquid line stop valve, and oil line ball valves.

q

5. The compressor oil level should be maintained

so that an oil level is always visible in one of the
compressor oil sightglasses. In other words, oil
level should always be maintained, running or not,
above the midpoint of the lower sightglass and
below the top of the upper sightglass.

«
...
96
97
98
99
100
...
»

Содержание MILLENNIUM YCAR0315

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MILLENNIUM YCAR0315

Бренд: S&A Страницы: 34

Бренд: SMC Networks Страницы: 192

Бренд: Poulan Pro Страницы: 8

Бренд: Daikin Страницы: 20

Бренд: Ruris Страницы: 82

LSBLG MCF Series

Бренд: Midea Страницы: 116

Бренд: Hansa Страницы: 30

Бренд: Fulgor Milano Страницы: 192

Бренд: Weed Eater Страницы: 24

Бренд: Weed Eater Страницы: 24

Бренд: Weed Eater Страницы: 24

Бренд: Weed Eater Страницы: 28

Бренд: Scheppach Страницы: 56

Бренд: Stihl Страницы: 276

Бренд: Land Pride Страницы: 32

Бренд: Garland Страницы: 180

Бренд: Garland Страницы: 180

Бренд: Daikin Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды