YOKOGAWA UTAdvanced UT35A Скачать руководство пользователя

Страница: 6 / 18

The following operating procedure describes an example of setting alarm setpoint (A1). <In case of UT35A>

1. Hold down the PARAMETER key for 3 seconds in the Operation Display to call up the [MODE] Menu Display.

2. Press the Right arrow key to display the [SP] Menu Display.

3. Press the SET/ENTER key to display the [SP] Parameter Setting Display.

4. Press the Down arrow key to display the [A1] Parameter Setting Display

5. Press the SET/ENTER key to blink the setpoint.

6. Press the Up or Down arrow key to change the setpoint.

7. Press the SET/ENTER key to register the setpoint (the setpoint stops blinking).

8. Press the PARAMETER key once to return to the Menu Display.

Press the DISPLAY key once to return to the Operation Display.

This completes the setting procedure.

How to Cancel Parameter Setting

To cancel parameter setting when a parameter is being set (setpoint is blinking), press the PARAMETER key once

(Change the setpoint using the Up/Down arrow keys to increase and decrease the value and the Left/Right
arrow keys to move between digits.)

Page 6 / 18

Содержание UTAdvanced UT35A


















