YOKOGAWA PX8000 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 202

background image

2-14

IM PX8000-02EN

Setting the Sensor Input Voltage Measurement Range (Vertical

Scale, RANGE Knob)

This section explains how to set a fixed range.
(If Auto Range in the AUX menu is set to ON, the measurement range changes depending on the
amplitude of the input signal.)

Turn the

RANGE

knob to set the sensor input voltage measurement range.

• Auto Range in the AUX menu is set to OFF.
• If you turn the RANGE knob when waveform acquisition is stopped, two values are shown on the

measurement range screen. The upper value is the measurement range for the displayed waveforms.
The lower value is the measurement range that you have specified. The new range will be applied the
next time waveform acquisition is started.

• If you do not operate the RANGE knob for approximately 3 seconds, the measurement range that you

are setting with the knob will disappear from the screen.

When the displayed waveform’s measurement range and the measurement range

that you have set are the same, only the bottom row is displayed.

Top row: Measurement range for the displayed waveforms

Bottom row: Measurement range that you have specified

Use the RANGE knob to display

the measurement range that is

currently being set.

Measurement Range Options and Units

Below are the available options for the RANGE knob, measurement range values, and

measurement range units that appear on the screen for when the zoom method is set to DIV and
the zoom magnification is set to ×1. If you change the zoom method or zoom magnification, what
appears on the screen will change accordingly.

• When Waveform Acquisition Is Stopped

Input

Signal

Type

Linear

Scaling Mode

Available Options

for the RANGE Knob

Measurement Range

Values

(that appear on the screen)

Measurement Range Units

(that appear on the screen)

Analog

OFF

(When the probe

attenuation is 10:1)

500.0mV,

1.000V,

2.500V,

5.000V,

10.00V,

25.00V,

50.00V,

100.0V,

250.0V,

500.0V,

1.000kV

The available options

vary depending on

the probe attenuation

setting.

Upper value:

RANGE knob value for the

displayed waveform

Lower value:

Available option value of

the RANGE knob

Upper unit value:

Same unit as the available

options for the RANGE

knob

Lower unit value:

Same unit as the available

options for the RANGE

knob

AX+B,

P1‒P2

Upper value:

Value obtained by

multiplying the available

option value of the RANGE

knob by the linear scaling

coefficient.

Lower value:

Available option value of

the RANGE knob

Upper unit value:

Unit specified on the AUX

setting screen

Lower unit value:

Same unit as the available

options for the RANGE

knob

Pulse

—

1, 2, 5, 10, 20, 50,

100, 200, 500, 1k,

2k, 5k, 10k, 20k, 50k,

100k, 200k, 500k, 1M

Upper value:

No display

Lower value:

Available option value of

the RANGE knob

Upper unit value:

No display

Lower unit value:

Unit specified on the AUX

setting screen

2.4 Configuring Sensor Input Voltage Measurements

«
...
29
30
31
32
33
...
»

Содержание PX8000











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PX8000

Бренд: Icare Страницы: 3

Бренд: Camille Bauer Страницы: 12

Бренд: Daewoo Страницы: 2

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: Daewoo Страницы: 17

Бренд: YATO Страницы: 36

Бренд: Vigor Equipment Страницы: 12

Бренд: NCS Страницы: 7

Бренд: Ferret Страницы: 18

Бренд: East Tester Страницы: 27

Бренд: Kawai Страницы: 2

Бренд: A&D Страницы: 2

Бренд: Hammond Страницы: 106

Бренд: GasQuip Страницы: 8

Бренд: Vega Страницы: 36

Бренд: janitza Страницы: 8

Бренд: BK Precision Страницы: 21

MJK MagFlux Series

Бренд: Xylem Страницы: 179

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды