30
5000-019C ASSEMBLY INSTRUCTIONS / PART ID
CASEIH 2412, 3412 12 ROW
Step 1:
Install each 5000-224 single mount to the corn head frame using 4
) 5/8” X 6” bolts, 2) 5000-341 mount straps, & 4) 5/8”
lock nuts per mount. Substitute 1) 2570-
131 5/8” – 11 X 4” X 8” U-Bolt for 1 mount strap & 2 5/8” X 6” bolts on each single
mount between rows 1 & 2 and 11 & 12 due to a support gusset prohibiting the strap to fit. Mounting bracket locations will be
between rows 1 & 2, 2 & 3, 4 & 5, 6 & 7, 7 & 8, 8 & 9, 10 & 11, and 11 & 12.
Step 2:
Install 1) 5000-
223 support strap on each mount. Use 2) ½” – 13 X 1 ½” bolts & 2) ½” – 13 flange whiz lock nuts to
attach
the support strap to the top set of holes on the mount plate & use 1) ½” – 13 X 2 ¼” bolt & 1) ½” – 13 flange whiz lock nut
to attach the support strap to the main pivot plate. Install the 5000-323 lock up pin in the storage location & secure each in place
with 2) 7 gauge cotter hairpin.
Step 3:
Install 1) 5000-318 pivot bushing in each mount. Attach 1) 5000-259 RH over bearing arm to each mount between rows
1 & 2, 6 & 7, 7 & 8, & 10 & 11. Attach 1) 5000-256 LH over bearing arm to each mount between rows 2 & 3, 4 & 5, 8 & 9, & 11 &
12. Align the lower hole on each arm with the pivot bushing &
insert a 5/8” X 3” bolt through & fasten with a 5/8” lock nut.
Step 4:
Install 1) 2570-
126 ¾” X 10” eyebolt to each mount. Attach each over bearing arm to the eyebolt using 1) 2510-121 5/8”
diameter shoulder bolt, 2) 2526-
449 5/8” flat washers, & 1) 2520-364 ½” jam lock nut. The 5/8” flat washers go on each side of the
eyebolt & inside the arm channel. The shoulder bolt should be inserted through the top hole on each arm.
Only tighten the ½” jam
lock nut until it makes slight contact with the over bearing arm.
Step 5:
Install the 2550-709 compression spring over each eyebolt, place the 2975-302 spring bushing over the eyebolt & onto
the compression spring, & secure with the 2520-
511 ¾” lock nut. Tighten the lock nut to be flush with the end of the eyebolt.
Step 6:
Install each 3 row roller mount. For rows 1
– 3, slide the roller mount into place between the plates on the over bearing
arm between rows 1 & 2 and 2 & 3. Use 2) 5000-378 spacer bushings, 2
) ½” X 3 ¾” bolts, & 2) ½” lock nuts to attach the roller
mount tube to each arm clamp. Repeat this process to attach the roller mount for rows 4
– 6 using the over bearing arm between
rows 4 & 5 and 6 & 7, rows 7
– 9 using the over bearing arms between rows 7 & 8 & 8 & 9, & rows 10 -12 using the over bearing
arms between rows 10 & 11 & 11 & 12. Do not tighten each roller mount into place until after the roller is installed so you can
center the roller if needed. Make sure the bearing support is on the back side of the roller mount tab.
Step 7:
Attach each roller to the roller mount using 2) 5000-322 shim washers, 2) 5000-
355 bearing assemblies, 6) ½” X 2 ½”
bolts, & 6) ½” lock nuts per roller.
NOTE: BEARING HOUSING SHOULD BE LUBRICATED WITH POLYUREA GREASE BEFORE USE AND THEN EVERY 100 HOURS OF OPERATION
Содержание 5000-005B
Страница 40: ...40 2565 771_REV_I 01 2024...
