14
5000-009C ASSEMBLY INSTRUCTIONS / PART ID
CASEIH 2206, 2406 NH98C/996 6 ROW
Step 1:
Install each 5000-
224 single mount to the corn head frame using 4) 5/8” X 6” bolts, 2) 5000-341 mount straps, & 4) 5/8”
lock nuts per mount. Mounting bracket locations will be between rows 1 & 2, 3 & 4, 4 & 5, & 5 & 6. Install the 5000-323 lock up
pin in the storage location & secure each in place with 2) 7 gauge cotter hairpin.
Step 2:
Install 1) 5000-
223 support strap on each mount. Use 2) ½” – 13 X 1 ½” bolts & 2) ½” – 13 flange whiz lock nuts to attach
the support strap to the top set of holes on the mount plate & use 1) ½” – 13 X 2 ¼” bolt & 1) ½” – 13 flange whiz lock nut to attach
the support strap to the main pivot plate.
Step 3:
Install 1) 5000-318 pivot bushing in each mount. Attach 1) 5000-259 RH over bearing arm to each mount between rows 3
& 4 and 4 & 5. Attach 1) 5000-256 LH over bearing arm to each mount between rows 1 & 2 and 5 & 6. Align the lower hole on
each arm with the pivot bushi
ng and insert a 5/8” X 3” bolt through & fasten with a 5/8” lock nut.
Step 4:
Install 1) 2570-
126 ¾” X 10” eyebolt to each mount. Attach each over bearing arm to the eyebolt using 1) 2510-121 5/8”
diameter shoulder bolt, 2) 2526-
449 5/8” flat washers, & 1) 2520-364 ½” jam lock nut. The 5/8” flat washers go on each side of the
eyebolt & inside the arm channel. The shoulder bolt should be inserted through the top hole on each arm.
Only tighten the ½” jam
lock nut until it makes slight contact with the over bearing arm.
Step 5:
Install the 2550-709 compression spring over each eyebolt, place the 2975-302 spring bushing over the eyebolt & onto the
compression spring, & secure with the 2520-
511 ¾” lock nut. Tighten the lock nut to be flush with the end of the eyebolt.
Step 6:
Install each 3 row roller mount. For rows 1
– 3, slide the 5000-261 longer roller mount into place between the plates on the
over bearing arm between rows 1 & 2 and 3 & 4. The bearing mount tab on the roller mount will be directly under the cut out on
the over bearing arm clamps between rows 3 & 4. Use 2) 5000-378 spacer bushings, 2
) ½” X 3 ¾” bolts, & 2) ½” lock nuts to
attach the roller mount tube to each arm clamp. Repeat this process to attach the 5000-254 roller mount for rows 4
– 6 using the
over bearing arm between rows 4 & 5 and 5 & 6. Do not tighten each roller mount into place until after the roller is installed so you
can center the roller if needed. Make sure the bearing support is on the back side of the roller mount tab.
Step 7:
Attach each roller to the roller mount using 2) 5000-322 shim washers, 2) 5000-
355 bearing assemblies, 6) ½” X 2 ½”
bolts, & 6) ½” lock nuts per roller.
NOTE: BEARING HOUSING SHOULD BE LUBRICATED WITH POLYUREA GREASE BEFORE USE AND THEN EVERY 100 HOURS OF OPERATION
Содержание 5000-005B
Страница 40: ...40 2565 771_REV_I 01 2024...
