18
5000-013B ASSEMBLY INSTRUCTIONS / PART ID
CASEIH 1063 6 ROW
Step 1:
Install each 5000-202 single mount & 5000-201 double mount to the corn head frame,
using 4) 5/8” X 6” bolts, 2) 5000-
319
mount straps, & 4) 5/8” lock nuts per mount. Single mount locations will be between rows 1 & 2 and 5 & 6. The double
mount will be located between rows 3 & 4
Step 2:
Install 2) 5000-309 support straps on each single mount & 4) 5000-
309 support straps on the double mount. Use 2) ½” –
13 X 2” carriage bolts & 2) ½” – 13 flange whiz lock nuts to attach the support straps to each single mount & use 4) ½” – 13 x 2”
carriag
e bolts & 4) ½” – 13 flange whiz lock nuts to attach the support straps to the double mount. Install the 5000-323 lock up
pin in the storage location & secure each in place with 2) 7 gauge cotter hairpin.
Step 3:
Install 1) 5000-318 pivot bushing in each single mount & 2) 5000-318 pivot bushings in the double mount. Attach 1) 5000-
256 LH over bearing arm to the single mount between rows 1 & 2. Install 1 5000-259 RH over bearing arm on the double mount
to the side that is closest to row 3. Install 1) 5000-256 LH over bearing arm to the double mount to the side that is closest to row 4.
Install 1) 5000-259 RH over bearing arm to the single mount between rows 5 & 6. Align the lower hole on each arm with the pivot
bushing and insert a 5/8” X 3” bolt through & fasten with a 5/8” lock nut.
Step 4:
Install 1) 2570-
126 ¾” X 10” eyebolt to each single mount & 2) 2570-126 ¾” X 10” eyebolt to the double mount. Attach
each over bearing arm to each eyebolt using 1) 2510-
121 5/8” diameter shoulder bolt, 2) 2526-449 5/8” flat washers, & 1) 2520-
364 ½” jam lock nut. The 5/8” flat washers go on each side of the eyebolt & inside the arm channel. The shoulder bolt should be
inserted through the top hole on each arm.
Only tighten the ½” jam lock nut until it makes slight contact with the over bearing arm.
Step 5:
Install the 2550-709 compression spring over each eyebolt, place the 2975-302 spring bushing over the eyebolt & onto
the compression spring, & secure with the 2520-
511 ¾” lock nut. Tighten the lock nut to be flush with the end of the eyebolt.
Step 6:
Install each 5000-261 long 3 row roller mount. For rows 1
– 3, slide the roller mount into place between the plates on the
over bearing arm between rows 1 & 2 and the arm between 3 & 4 that is closer to row 3. Use 2) 5000-378 spacer bushings, 2
) ½”
X 3 ¾” bolts, & 2) ½” lock nuts to attach the roller mount tube to each arm clamp. Repeat this process to attach the roller mount
for rows 4
– 6 using the over bearing arm between rows 3 & 4 (arm that is closer to row 4) and 5 & 6. Do not tighten each roller
mount into place until after the roller is installed so you can center the roller if needed. Make sure the bearing support is on the
back side of the roller mount tab.
Step 7:
Attach each roller to the 3 row roller mount using 2) 5000-322 shim washers, 2) 5000-355 bearing
assemblies, 6) ½” X 2 ½” bolts, & 6) ½” lock nuts per roller.
NOTE: BEARING HOUSING SHOULD BE LUBRICATED WITH POLYUREA GREASE BEFORE USE AND THEN EVERY 100 HOURS OF OPERATION
Содержание 5000-005B
Страница 40: ...40 2565 771_REV_I 01 2024...
