20
5000-014C ASSEMBLY INSTRUCTIONS / PART ID
CASEIH 1083 8 ROW
Step 1:
Install each 5000-202 single mount & 5000-201 double mount to the corn head frame,
using 4) 5/8” X 6” bolts, 2) 5000-
319 mount straps,
& 4) 5/8” lock nuts per mount. Single mount locations will be between rows 1 & 2, 2 & 3, 6 & 7, and 7 & 8.
The double mount will be located between rows 4 & 5.
Step 2:
Install 2) 5000-309 support straps on each single mount & 4) 5000-309 support straps on
the double mount. Use 2) ½” –
13 X 2” carriage bolts & 2) ½” – 13 flange whiz lock nuts to attach the support straps to each single mount & use 4) ½” – 13 x 2”
carriage bolts & 4) ½” – 13 flange whiz lock nuts to attach the support straps to the double mount. Install the 5000-323 lock up pin
in the storage location & secure each in place with 2) 7 gauge cotter hairpin.
Step 3:
Install 1) 5000-318 pivot bushing in each single mount & 2) 5000-318 pivot bushings in the double mount. Attach 1) 5000-
256 LH over bearing arm to the single mount between rows 2 & 3 and 7 & 8. Install 1) 5000-259 RH over bearing arm on the
double mount to the side that is closest to row 4. Install 1) 5000-256 LH over bearing arm to the double mount to the side that is
closest to row 5. Install 1) 5000-259 RH over bearing arm to the single mount between rows 1 & 2 and 6 & 7. Align the lower hole
on each arm with the pivot bushing and insert a 5/8” X 3” bolt through & fasten with a 5/8” lock nut.
Step 4:
Install 1) 2570-
126 ¾” X 10” eyebolt to each single mount & 2) 2570-126 ¾” X 10” eyebolt to the double mount. Attach
each over bearing arm to each eyebolt using 1) 2510-
121 5/8” diameter shoulder bolt, 2) 2526-449 5/8” flat washers, & 1) 2520-
364 ½” jam lock nut. The 5/8” flat washers go on each side of the eyebolt & inside the arm channel. The shoulder bolt should be
inserted through the top hole on each arm.
Only tighten the ½” jam lock nut until it makes slight contact with the over bearing arm.
Step 5:
Install the 2550-709 compression spring over each eyebolt, place the 2975-302 spring bushing over the eyebolt & onto the
compression spring, & secure with the 2520-
511 ¾” lock nut. Tighten the lock nut to be flush with the end of the eyebolt.
Step 6:
Install each 3 row roller mount. For rows 1
– 3, slide the roller mount into place between the plates on the over bearing
arm between rows 1 & 2 and 2 & 3. Use 2) 5000-378 spacer bushings, 2
) ½” X 3 ¾” bolts, & 2) ½” lock nuts to attach the roller
mount tube to each arm clamp. Repeat this process to attach the roller mount for rows 6
– 8 using the over bearing arm between
rows 6 & 7 and 7 & 8. Install the 2 row roller mount to the over bearing arms between rows 4 & 5. Do not tighten each roller mount
into place until after the roller is installed so you can center the roller if needed. Make sure the bearing support is on the back side
of the roller mount tab.
Step 7:
Attach each roller to the roller mount using 2) 5000-322 shim washers, 2) 5000-
355 bearing assemblies, 6) ½” X 2 ½”
bolts, &
6) ½” lock nuts per roller.
NOTE: BEARING HOUSING SHOULD BE LUBRICATED WITH POLYUREA GREASE BEFORE USE AND THEN EVERY 100 HOURS OF OPERATION
Содержание 5000-005B
Страница 40: ...40 2565 771_REV_I 01 2024...
