YATO YT-82810, Оригинальное руководство пользователя

Страница: 17 / 128

17
GB
O R I G I N A L I N S T R U C T I O N S
the fl oor. if the edge of the saw is unprotected, the sawing machine will retract cutting anything it contacts accidentally. Remember
the saw needs time to come to a halt, once the machine is turned o ff .
Additional safety instructions for sawing machines with a splitting wedge
Use an appropriate splitting edge for the given saw. The splitting edge must be thicker than the body of the saw, but thinner
than the distance between the teeth of the saw.
Adjust the splitting edge in accordance with the description in this manual. Incorrect setting, a wrong position or misalign-
ment may make the splitting edge useless in the context of prevention of backward recoil.
Always use a splitting, except for deep cutting. The splitting edge must be installed again after deep cutting. The splitting edge
causes disturbance during deep cutting and may cause backward recoil.
In order to function correctly, the splitting edge must be introduced into the element being processed. The splitting edge
is useless in prevention of backward recoil during short cuts.
Do not operate the sawing machine, if the splitting edge is bent. Even slight bends may slower the closing of the guard.
ASSEMBLY OF EQUIPMENT
ATTENTION! The installation of the equipment may be done only with disconnected power supply. Remove the battery pack
from the power tool socket!
The saw machine is supplied complete, After opening the factory packaging you should check whether all items were packed.
Then check the connections status and, if necessary, tighten the screw connecting the base with fi xed guard and tighten the
screws, which are fastening the splitting wedge, if the saw machine is equipped with it. Before the fi rst use, you should mount the
circular saw blade.
PREPARING FOR OPERATION
Before starting any work you should check whether the housing and the battery are not damaged. In the case of damage any
further work is prohibited.
Attention! All activities associated with the installation and replacement of circular saw blades, their adjustment and
the maintenance of a power tool must be carried out when the operating voltage of the saw machine is switched o ff ,
therefore, before the further proceedings, you should carry out the following steps: Remove the battery pack from the
power tool socket!
ATTENTION! All the operations mentioned in this point must be realised with the power supply o ff .
- the battery must be disconnected from the tool!
Safety recommendations for battery loading
Attention! Before loading may start make sure the body of the charger, the cable and the plug are not broken or damaged. It
is prohibited to use a damaged loading dock and charger! For the purpose of loading batteries only the charging dock and the
charger provided may be used. Using another charger may be a cause of fi re or damage the tool. Batteries may be charged only
in a dry room, protected from unauthorised persons, particularly children. Do not use the charging dock and the charger without
permanent supervision of an adult! If it is necessary to leave the room where loading is taking place, it is required to disconnect the
charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange
smell is emitted, etc., it is required to immediately remove the plug of the charger from the mains socket!
The drill and automatic return screwdriver is provided with an unloaded battery, so before work may commence, it is required
to charge it following the procedure below, using the charger and charging dock provided. Li-ION batteries do not show the so
called “memory e ff ect”, so it is allowed to charge them at any moment. However, it is recommended to discharge them during
normal work, and then load them to their full capacity. If due to the nature of the task it is not possible to do so each time, then it
is required to do it at least from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting the
electrodes, since this would cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the
electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through ap-
proximately 500 „loading - discharging” cycles. The battery must be stored between 0 and 30°C, at the relative humidity of 50%. In
order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of prolonged
storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this would
reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic unloading depends