
11
O R I G I N A L I N S T R U C T I O N S
EN
PRODUCT OVERVIEW
The ultrasonic workshop cleaner is suitable for removing dirt from various types of components and for cleaning tools. Ultrasonic
cleaning enables e
ff
ective cleaning, degreasing, even in hard-to-reach areas, without having to take components apart or small
parts. Proper, reliable and safe operation of the product requires its correct use, that is why you should:
Read the entire instructions manual before the
fi
rst use of the product and keep it for future reference.
The supplier shall not be held liable for any damage or injury resulting from improper use of the product, failure to observe the
safety regulations and recommendations of this instructions manual. Use of the product for purposes other than those for which it
was intended shall cause the loss of the user’s rights to the warranty and under statutory warranty.
COMPONENTS
The product is supplied complete and does not require assembly. Preparations described later in this manual are also required.
Parameter
Unit
Value
Part No.
YT-55801
YT-55803
Rated voltage
[V~]
220-240
220-240
Rated frequency
[Hz]
50/60
50/60
Rated power
[W]
480
600
Insulation class
I
I
Protection rating
IPX0
IPX0
Size of basket (L x W x H)
[mm]
500 x 300 x 150
500 x 300 x 200
Machine dimension (L, x W x H)
[mm]
500 x 325 x 285
500 x 325 x 325
Operating temperature
[°C]
0 ~ +80
0 ~ +80
Ultrasound frequency
[kHz]
40
40
Operation time
[min]
0-30
0-30
fl
uid tank capacity
[l]
22
30
Drain valve thread size
G1/2
G1/2
Net weight
[kg]
9.5
11
SAFETY INSTRUCTIONS
Recommendations concerning transport and installation of the product
NOTE!
The product may only be placed on a hard,
fl
at, level, and non-
fl
ammable surface.
The surface should be able to withstand the weight of the appliance itself and of the parts
and
fl
uid it contains. Ensure that there is a minimum distance of 10 cm around the side walls
of the product, and do not place non-high temperature resistant materials above the product.
This will allow for the proper ventilation of the product. Do not place near edges of, e.g., a
table. Do not place any electrical equipment above the product. During operation, water va-
pour is released, which can cause a short circuit in the electrical system and lead to electric
shock. It is forbidden to drill any holes in the product, as well as making any other modi
fi
ca-
tions of the product not described in the manual. Move the product only when cooled down,
grasping the housing. Do not move the product by pulling the power cord. No metal objects
or surfaces should be placed on or near the back of the product. Do not place the product in
high temperature areas. The temperature at the place of installation and use of the product
must be within the range of +10°C ÷ +38°C, and the relative humidity must be below 90%
without water vapour condensation.
Содержание YT-55801
