YASKAWA PVI 50TL Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 104

YASKAWA PVI 50TL Скачать руководство пользователя страница 78

DOCR-070645-E

Page 78 of 102

4.4.3 Power ON/OFF

A manual power cycle ON/OFF is required after any parameter change, after getting
an error message or updating the software. The unit will automatically go into the
OFF state. Press ESC or ENT to enter into the Main Menu, then press ENT and go to
the submenu “Power On/OFF”. Then move the cursor to “ON” and press ENT to start
the inverter, the inverter will start up normally and operate if the start-up conditions
are met.
Normally it is not necessary to turn OFF the inverter, but if this is needed, you can do
so from this menu simply by selecting “OFF” and pressing ENT to confirm.

4.4.4 History

Move the cursor to “4 History” in the main interface. Press ENT to check the history
information, as shown in Figure 4.20. There are 2 submenus in “2 History”: “Running
History” and “Fault Record”.
(1) The log can store up 100 running history messages in the “Running History”
menu.
(2) The log can store up 100 fault records in the “Fault Record” menu.

History Record

Running Record

Fault Record

Current Error

Current Error

P1/1

Date

Error

2015/10/22 12:20:08

ArcboardErr

2015/10/22 12:20:08

2015/10/22 12:20:08

Fault0040

2015/10/22 12:20:08

2015/10/22 12:20:08

Time

Fault0040

Fault0040

Fault0040

Fault Record

P1/1

Num

Date

Error

001

15/10/22 12:20:08

003

15/10/22 12:20:08

002

15/10/22 12:20:08

004

15/10/22 12:20:08

005

15/10/22 12:20:08

Time

Fault0040

Fault0040

Fault0040

Fault0040

ArcboardErr

Action

ON

ON

ON

ON

ON

Running Record

P1/1

Num

Date

Event

001

15/10/22 12:20:08

003

15/10/22 12:20:08

002

15/10/22 12:20:08

004

15/10/22 12:20:08

006

15/10/22 12:20:08

005

15/10/22 12:20:08

Fault

Standby

Standby

On-grid

Off-grid

SysStart

Time

Figure 4-20 History Menu and Submenu

«
...
76
77
78
79
80
...
»

Содержание PVI 50TL









































































































Отзывы:

Нет отзывов