manualshive.com logo in svg

YASKAWA D1000 Series, Инструкция по эксплуатации, Страница: 198 / 251

Поделиться
Скачать
YASKAWA D1000 Series Скачать руководство пользователя страница 198

198

 

YASKAWA ELECTRIC

 TOEP C710656 07A YASKAWA Power Regenerative Converter - D1000 Instruction Manual

C.1  MEMOBUS/Modbus Configuration

C.1 MEMOBUS/Modbus Configuration

Converter can be controlled from a PLC or other master device via serial communications using the MEMOBUS/Modbus 
protocol.

MEMOBUS/Modbus communications can be configured using one master (PLC) and up to 255 slaves. The converter

has slave functionality only, and serial communication is normally initiated from the master and responded to by the 
slaves.

The master communicates with the specified slave converter. The address or node for each slave must be set prior so the 
master can communicate with the slave at that address. A slave that receives a command from the master will perform the 
specified function and send a response back to the master.

Figure C.1  

Figure C.1  Connecting Multiple Converter to a PLC

Master (PLC or other)

Slave (converter)

D1000

Содержание D1000 Series




























































































































































































































































Отзывы:

Нет отзывов