YASKAWA D1000 Series Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 251

YASKAWA D1000 Series Скачать руководство пользователя страница 178

B.2 Parameter Tables

178

YASKAWA ELECTRIC

TOEP C710656 07A YASKAWA Power Regenerative Converter - D1000 Instruction Manual

◆

d: References

Reference parameters set the value of the DC bus voltage reference.

◆

F: Options

F parameters program the converter for communication options and to function with option cards.

C7-43

(112AH)

Input Voltage Offset
Adjustment

Vac Bias Adj Sel

There is normally no need to change this parameter from
the default value. This parameter is for factory setting.
If the setting is not correct, the converter may be damaged.
0: Standard
1: Start offset adjustment. (The parameter returns to 0 after
it is set.)
2: Offset adjustment not required. (The parameter returns
to 0 after it is set.)

Default: 0
Range: 0 to 2

C7-44

(112BH)

Gain for Active
Damping 3

Damping Gain 3

There is normally no need to change this parameter from
the default value.

Default: 0.00
Min.: 0.00
Max.: 1.00

C7-47

(112EH)

Adjustment Reactor
1

L1 Compensation

There is normally no need to change this parameter from
the default value.
Set this parameter to the value that is specified by the
manufacturer when using a filter such as the DC5.

Min.: 00.000
Max.: 65.000

C7-50

(113BH)

Converter Ready
ON Delay Time

Conv READY delay

Sets the delay time to turn on the Converter Ready signal
(H2-

=6).

Default: 0 ms
Min.: 0
Max.: 500

C7-51

(113CH)

Adjustment Reactor
2

L2 Compensation

There is normally no need to change this parameter from
the default value.
Set this parameter to the value that is specified by the
manufacturer when using a filter such as the DC5.

Min.: 00.000
Max.: 65.000

<1> This parameter is not available in model 4A0630.

<2> Default setting is dependent on parameter o2-04, Drive Model Selection.

No.

(Addr.

Hex)

Name

LCD Display

Description

Values

d8: DC Bus Voltage Reference

d8-01

(2B9H)

DC Bus Voltage
Reference

Vpn Volt Ref

Sets the DC bus voltage reference in volts.
Yaskawa recommends setting a value that is 1.5 times the
set value of the Power Supply Voltage (U1-54).

200 V Class

Default: 330 V
Range:300 V to
360 V

400 V Class

Default: 660 V
Range: 600 V to
730 V

No.

(Addr.

Hex)

Name

LCD Display

Description

Values

F4: Analog Monitor Card (AO-A3)

F4-01

(391H)

Terminal V1
Monitor Selection

AO Ch1 Select

Sets the monitor signal for output from terminal V1. Set
this parameter to the last three digits of the desired
U

-

monitor. Some U parameters are available only

in certain control modes.

Default: 0
Min.: 000
Max.: 408

No.

(Addr.

Hex)

Name

LCD Display

Description

Values

«
...
176
177
178
179
180
...
»

Содержание D1000 Series




























































































































































































































































Отзывы:

Нет отзывов