manualshive.com logo in svg

YASKAWA D1000 Series, Инструкция по эксплуатации, Страница: 186 / 251

Поделиться
Скачать
YASKAWA D1000 Series Скачать руководство пользователя страница 186

B.2  Parameter Tables

186

 

YASKAWA ELECTRIC

 TOEP C710656 07A YASKAWA Power Regenerative Converter - D1000 Instruction Manual

L8-10

(4B6H)

Heatsink Cooling 
Fan Operation 
Selection

Fan On/Off Sel
0: Dur Run (OffDly)
1: Always On

0: During run only. Fan operates only during run for L8-11 
seconds after stop.
1: Fan always on. Cooling fan operates whenever the 
converter is powered up.

Default: 0
Min.: 0
Max.: 1

L8-11

(4B7H)

Heatsink Cooling 
Fan Off Delay Time

Fan Delay Time

Sets a delay time to shut off the cooling fan after the Run 
command is removed when L8-10 = 0.

Default: 60 s
Min.: 0 s
Max.: 300 s

L8-12

(4B8H) 

Ambient 
Temperature Setting

Ambient Temp

Enter the ambient temperature. This value adjusts the oL2 
detection level.

Default: 40

°

C

Min.: -10

°

C

Max.: 50

°

C

L8-35

(4ECH)

Installation Method 
Selection

Installation Sel
0: IP00/OpenChassis
1: Side-by-Side
3: ExternalHeatsink

0: IP00/IP20/Open-Chassis Enclosure
1: Side-by-Side mounting
3: External Heatsink Installation

Default: 

<2>

Min.: 0
Max.: 3

L8-41

(4F2H)

High Current Alarm 
Selection

High Cur Alm Sel
0: Disabled
1: Enabled

0: Disabled
1: Enabled. An alarm is triggered at output currents above 
150% of converter rated current.

Default: 0
Min.: 0
Max.: 1

L8-65

(66FH)

Power Supply Fault 
Detection Selection

Vpn Ripple Sel  
0: Disabled  
1: Coast to Stop  
2: Alarm Only 

There is normally no need to change this parameter from 
the default value.
Monitors the ripple of DC BUS voltage and detects Input 
Power Supply Fault(PF2) when the ripple is too bad. 
0: No detection 
1: Stop operation (fault) 
2: Continue operation (minor fault) 

Default: 0
Min.: 0
Max.: 2

L8-66

(670H)

Power Supply Fault 
Detection Voltage 
Level

Vpn Ripple Lvl 

There is normally no need to change this parameter from 
the default value. The main circuit DC voltage ripple is 
monitored in a cycle of 200 ms. If the difference between 
the maximum and minimum values of the ripple exceeds 
the value that is set in L8-66 for the number of times that is 
set in L8-67, a power supply fault is detected.

200V Class

Default: <1>
Min.: 1
Max.: 200

400V Class

Default: <1>
Min.: 1
Max.: 200

L8-67

(671H)

Number of Times of 
Power Supply Fault 
for Detection

Vpn Ripple Cnt 

Default: 5
Min.: 1
Max.: 10

L8-69

(673H)

Input Phase Loss 
Protection Selection 
3

AC Phase Imb Det  
0: Disabled  
1: Enabled 

Sets whether to enable or disable the protective function 
for the converter when there is an input phase loss. 
0: Disabled 
1: Enabled (Detect input phase loss and power supply 
imbalance.) 

Default: 1
Min.: 0
Max.: 1

L8-78

(2CCH)

Module Phase Loss 
(LF3) Protection

LF3 Det Sel  
0: Disabled  
1: Enabled 

Enables phase loss protection for the input terminals R/L1, 
S/L2, T/L3 or R1/L11, S1/L21, T1/L31.
0: Disable
1: Enable

Note:

 This parameter is available in model 4A0630.

Default: 1
Min.: 0
Max.: 1

<2> Default setting is dependent on parameter o2-04, Drive Model Selection.

No.

(Addr.

Hex)

Name

LCD Display

Description

Values

Содержание D1000 Series




























































































































































































































































Отзывы:

Нет отзывов