manualshive.com logo in svg

YASKAWA D1000 Series, Инструкция по эксплуатации, Страница: 111 / 251

Поделиться
Скачать
YASKAWA D1000 Series Скачать руководство пользователя страница 111

5.2  Fault Detection

 

YASKAWA ELECTRIC

 TOEP C710656 07A YASKAWA Power Regenerative Converter - D1000 Instruction Manual

 111

Tr

ou

blesh

oot

ing

5

Digital Operator 

Display

Fault Name

Details

oC

Overcurrent

converter sensors detected an output current greater than the specified overcurrent level.

Cause

Possible Solution

One of the cables has shorted out or there is a 
grounding problem

• Check the motor cables.
• Remove the short circuit and reapply power to the converter.
• Check the resistance between the motor cables and the ground terminal 

.

• Replace damaged cables.

The load is too heavy

• Measure the current flowing into the converter.
• Replace the converter with a larger capacity converter if the current value exceeds the rated 

current.

• Determine if there is sudden fluctuation in the current level.
• Reduce the load to avoid sudden changes in the current level or switch to a larger converter.

converter fails to operate properly due to noise 
interference

• Review the possible solutions provided for handling noise interference.
• Review the section on handling noise interference on page 393 and check the control circuit 

lines, main circuit lines, and ground wiring.

The wiring of the power supply voltage 
detection circuits (

) and 

the wiring of the main circuit terminals 
(R/L1, S/L2, and T/L3) is not correct.

• Correct the wiring.

The voltage on the power supply side is very 
low.

Check the wiring.

• Correct the wiring.

Check the load on the power supply of peripheral devices that are connected to the same power 
supply line.

• Reduce the load.

Digital Operator 

Display

Fault Name

Details

oFA00

Option Card 

Connection Error at 
Option Port CN5-A

Option compatibility error

Cause

Possible Solution

The option card installed into port CN5-A is 
incompatible with the converter.

Check if the converter supports the option card to be installed. Contact Yaskawa for assistance.

Digital Operator 

Display

Fault Name

Details

oFA01

Option Card Fault at 

Option Port CN5-A

Option not properly connected

Cause

Possible Solution

The option card connection to port CN5-A is
faulty

• Turn off the power and reconnect the option card.

Digital Operator 

Display

Fault Name

Details

oFA02

Same Type of Option 

Card Already 

Connected

The combination of the option cards that are connected is not correct.

Cause

Possible Solution

The same option cards or the same type of 
option cards are connected to CN5-A, CN5-B, 
and CN5-C.

• Connect the option cards correctly.

r1/ 11,    1/ 21, t1/ 31

Содержание D1000 Series




























































































































































































































































Отзывы:

Нет отзывов