Setting User Constants
4.2.4 Operation Mode
- 16
Func-
Con-
Name
Output Signal Levels for
Min
Valid Access Levels
Func-
tion
Con
stant
No.
Digital Operator
Display
Function
Output Signal Levels for
Multi-function Analog Out-
puts
Min.
Units
Open Loop
Vector
Flux
Vector
U3-01
Most recent fault
Information on the last fault
Q
Q
U3-01
Last Fault
Information on the last fault.
Q
Q
U3-02
Second most re-
cent fault
Information on the 2
nd
to last
fault
Q
Q
U3 02
Fault Message 2
fault.
Q
Q
U3-03
Third most recent
fault
Information on the 3
rd
to last
fault
Q
Q
U3 03
Fault Message 3
fault.
Q
Q
U3-04
Fourth/oldest fault
Information on the 4
th
to last
Q
Q
Fault
U3-04
Fault Message 4
Information on the 4 to last
fault.
Q
Q
Fault
histo-
ry
(See
U3-05
Cumulative opera-
tion time at fault
Elapsed running or power-on
time when the last fault oc-
Can’t be output.
1 hr
Q
Q
y
(See
note.)
U3 05
Elapsed Time 1
time when the last fault oc
curred.
1 hr
Q
Q
note.)
U3-06
Accumulated time
of second fault
Elapsed running or power-on
time when the 2
nd
to last fault
1 hr
Q
Q
U3 06
Elapsed Time 2
time when the 2
to last fault
occurred.
1 hr
Q
Q
U3-07
Accumulated time
of third fault
Elapsed running or power-on
time when the 3
rd
to last fault
1 hr
Q
Q
U3 07
Elapsed Time 3
time when the 3
to last fault
occurred.
1 hr
Q
Q
U3-08
Accumulated time
of fourth/oldest
fault
Elapsed running or power-on
time when the 4
th
to last fault
occurred
1 hr
Q
Q
Elapsed Time 4
occurred.
Note Faults CPF00, 01, 02, 03, UV1 and UV2 are not recorded in the fault history.
J
Monitoring at Startup
In operation mode, the frequency reference, output frequency, output current, and output voltage can be
monitored immediately if the factory presets are being used. One of these four values, the output voltage,
can be changed to a different monitor item. When an item other than the output voltage is to be monitored,
set that value in user constant o1-01 (Monitor selection). Refer to the example procedure given later in this
manual.
When the power is turned ON, the frequency reference will appear in the Unit’s data display if the factor
presets are being used. Any one of the four values monitored at startup (frequency reference, output fre-
quency, output current, or the value set in user constant o1-01) can be selected to appear when the power
is turned ON.
The value that appears at startup is determined by user constant o1-02 (Monitor selection after power up).
User constants o1-01 and o1-02 can be changed in the Basic or Advanced access levels. These user
constants can be changed during operation.
J
Monitor Displays
The following notation is used in this manual when describing user constants.
User
Change
during
Setting
Factory
Valid Access Levels
User
Constant
Number
Display Name
during
Opera-
tion
Setting
Range
Unit
Factory
Setting
Open Loop
Vector
Flux Vector
o1-01
Monitor selection
4 to 28
--
6
B
B
Use the last two digits from the U1 Monitor list (U1-
) to select a value. For example, the torque refer-
ence is U1-09, so input 9 to select the torque reference.
Change during
Indicates whether or not the constant can be changed during operation.
Change during
Operation
Can be changed during operation.
Operation
Cannot be changed during operation.
Setting Range
The setting range for the constant.
Units
The unit used to set the constant (“--” indicates that no unit is used).
Factory Setting
The value preset at the factory. (There are different factory settings for each control meth-
od, i.e., if the control method is changed, the factory setting can also change.)
Indicates the control methods and access levels under which the constant can be accessed
and set.
Valid Access
Q
Accessible/settable under Quick-start.
Valid Access
Levels
B
Accessible/settable under Quick-start or Basic.
A
Accessible/settable under all access levels (Quick-start, Basic, and Advanced).
Not accessible/settable in the specified control method.
4