YASKAWA 175932-1CD Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

YASKAWA 175932-1CD Скачать руководство пользователя страница 29

2-4

175932-1CD

175932-1CD

EcoTrim ET-1024 System

2 Equipment Description
2.4 Operator Station

2.4.1 Cycle Start/Cycle Latched

The operation of the Cycle Start/Cycle Latched button depends upon the
structure of the Control Master job.

The green Cycle Start/Cycle Latched button, located on the Operator
Station, initiates a positioner sweep cycle if the robot is in the Home
position. If the Cycle Start/Cycle Latched button is pressed while the robot
is outside Home position, the Cycle Start command does not execute and
the positioner does not sweep until the robot returns to Home position.

The green Cycle Latched lamp illuminates when the Cycle Start/Cycle
Latched button is pressed during operation. When the lamp is illuminated,
the positioner will sweep and the robot will begin trimming immediately
after the current cycle is complete and the robot has returned to Home
position. It is not necessary to wait for the robot to finish trimming and
return to Home position before pressing the Cycle Start/Cycle Latched
button. Pressing the Cycle Start/Cycle Latched button while the robot is
still in motion latches the Cycle Start command into the controller. If a
person or object enters the safety zone created by the light curtain
system, the Cycle Start command will unlatch and the positioner will not
sweep.

2.4.2 Emergency Stop (E-STOP)

Pressing the red Emergency Stop (E-STOP) button on the Operator
Station stops all system operation and removes servo power. Brakes are
applied to the robot, and all positioner motion is stopped.

2.4.3 Robot Hold

Pressing the red Robot Hold button stops robot operation and interrupts
the job until the operator presses the green Start button to resume
operation. Operation resumes at the point in the program where the Robot
Hold state was initiated.

2.4.4 Alarm

A red Alarm lamp illuminates to indicate that the DX200 controller has
encountered an alarm condition.

2.4.5 Positioner Auto/Manual

The Positioner Auto/Manual switch is used to select automatic or manual
mode for the MSR rotary positioner. When the switch is set to the Auto
position, the robot trims the parts immediately after the positioner sweeps.
When the switch is set to the Manual position, the robot does not
immediately start to trim after the positioner sweeps and remain in Home
position.

2.4.6 Start

Pressing the green Start button starts the current, active job. The Operator
Station must be enabled and servo power must be ON for the Start button
to function.

NOTE

The Positioner Auto/Manual signal depends upon the
structure of the Control Master job.

29 of 64

«
...
27
28
29
30
31
...
»

Содержание 175932-1CD

































































Отзывы:

Нет отзывов