Yanmar 2V Series Скачать руководство пользователя | Manualshive

Страница: 47 / 112

background image

BEFORE YOU OPERATE

2V Operation Manual

31

DIESEL FUEL

Diesel Fuel Specifications

Diesel fuel should comply with the following
specifications. The table lists several worldwide
specifications for diesel fuels.

Additional Technical Fuel Requirements

• The fuel cetane number should be equal to 45 or

higher.

• The sulfur content must not exceed 0.5% by

volume. Less than 0.05% is preferred.

• Bio-Diesel fuels.

See Bio-Diesel Fuels on

page 31

• NEVER mix kerosene, used engine oil, or

residual fuels with the diesel fuel.

• Water and sediment in the fuel should not exceed

0.05% by volume.

• Keep the fuel tank and fuel-handling equipment

clean at all times.

• Poor quality fuel can reduce engine performance

and / or cause engine damage.

• Fuel additives are not recommended. Some fuel

additives may cause poor engine performance.
Consult your Yanmar representative for more
information.

• Ash content not to exceed 0.01% by volume.

• Carbon residue content not to exceed 0.35% by

volume. Less than 0.1% is preferred.

• Total aromatics content should not exceed 35%

by volume. Less than 30% is preferred.

• PAH (polycyclic aromatic hydrocarbons) content

should be below 10% by volume.

• Metal content of Na, Mg, Si, and Al should be

equal to or lower than 1 mass ppm. (Test analysis
method JPI-5S-44-95)

• Lubricity: Wear mark of WS1.4 should be Max.

0.018 in (460

µ

m) at HFRR test.

Bio-Diesel Fuels

In Europe and in the United States, as well as some
other countries, non-mineral oil based fuel
resources such as RME (Rapeseed Methyl Ester)
and SOME (Soybean Methyl Ester), collectively
known as FAME (Fatty Acid Methyl Esters), are
being used as extenders for mineral oil derived
diesel fuels.

Yanmar approves the use of bio-diesel fuels that do
not exceed a blend of 5% (by volume) of FAME with
95% (by volume) of approved mineral oil derived
diesel fuel. Such bio-diesel fuels are known in the
marketplace as B5 diesel fuels.

These B5 diesel fuels must meet certain
requirements.

1. The bio-fuels must meet the minimum

specifications for the country in which they are
used.

• In Europe, bio-diesel fuels must comply with

the European Standard EN14214.

• In the United States, bio-diesel fuels must

comply with the American Standard ASTM D-
6751.

2. Bio-fuels should be purchased only from

recognized and authorized diesel fuel suppliers.

Diesel Fuel Specification

Location

No. 2-D, No. 1-D, ASTM D975-94

USA

EN590:96

European Union

ISO 8217 DMX

International

BS 2869-A1 or A2

United Kingdom

JIS K2204 Grade No.2

Japan

KSM-2610

Korea

GB252 China

«
...
45
46
47
48
49
...
»

Содержание 2V Series

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 2V Series

Бренд: Wartsila Страницы: 168

Бренд: GAS GAS Страницы: 71

Бренд: ZIEHL-ABEGG Страницы: 84

HOME MOTION Roll Up 28 WT

Бренд: SOMFY Страницы: 10

Бренд: Schartec Страницы: 16

Бренд: Hatz Diesel Страницы: 48

Бренд: Volvo Penta Страницы: 44

Бренд: Volvo Penta Страницы: 90

Бренд: New Holland Страницы: 41

Бренд: panthera Страницы: 12

Бренд: Stiga Страницы: 51

Бренд: Tomahawk Страницы: 20

Бренд: Team Biland Страницы: 18

Бренд: CRRC-pro Страницы: 8

Бренд: SEW-Eurodrive Страницы: 4

Бренд: FAW Jiefang Automotive Страницы: 57

WEST EUROTECH 36 v1

Бренд: Weston UK Страницы: 4

Бренд: XICOY Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды