Yamaha V150D Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 81

background image

Basic components

12

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

6. Throttle
7. Fully open

1. Neutral interlock trigger

«
...
15
16
17
18
19
...
»

Содержание V150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для V150D

Бренд: Acer Страницы: 2

Бренд: AOpen Страницы: 8

PowerSoC CY3267

Бренд: Cypress Страницы: 12

Бренд: A-Trend Страницы: 60

Motherboard DJ800

Бренд: IWILL Страницы: 52

VAR-SOM-MX8M-NANO

Бренд: Variscite Страницы: 2

Бренд: ASROCK Страницы: 95

Бренд: Telit Wireless Solutions Страницы: 47

Бренд: Intel Страницы: 73

Бренд: IDT Страницы: 39

iEi ROCKY-4782E2V

Бренд: ICP Electronics Страницы: 52

Бренд: Award Страницы: 60

Бренд: Gigabyte Страницы: 40

Бренд: Maxtang Страницы: 14

Бренд: Supermicro Страницы: 97

Бренд: Honeywell Страницы: 16

Gamewell FCI ILI-MB-E3

Бренд: Honeywell Страницы: 18

GENT S4-INTERFACE-PROG

Бренд: Honeywell Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды