Yamaha V150D Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 81

background image

Basic components

19

turning on the main switch to make sure all

segments come on.

NOTE:

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired unit of measurement by set-
ting the selector switch on the back of the

gauge. See the illustration for settings.

EMU26610

Trim meter

This gauge shows the trim angle of your out-
board motor.

NOTE:

Memorize the trim angles that work best for
your boat under different conditions. Adjust
the trim angle to the desired setting with the

power trim and tilt switch.

EMU26620

Trim meter (digital type)

This meter shows the trim angle of your out-
board motor.

NOTE:

●

Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired using
the power trim and tilt switch.

●

If the trim angle of your motor exceeds the
trim operating range, the top segment on

the trim meter display will blink.

EMU26650

Hour meter (digital type)

This meter shows the number of hours the
engine has been run. It can be set to show
the total number of hours or the number of
hours for the current trip. The display can
also be turned on and off.

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

ZMU04581

ZMU01869

ZMU01870

«
...
22
23
24
25
26
...
»

Содержание V150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для V150D

Бренд: IEI Technology Страницы: 211

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 8

Бренд: OLIMEX Страницы: 12

Бренд: ASRock Industrial Страницы: 44

Бренд: Supermicro Страницы: 2

Airborne WLNN-EK-DP55x

Бренд: B&B Electronics Страницы: 6

Бренд: Texas Instruments Страницы: 9

Бренд: IEI Technology Страницы: 153

Бренд: EPOX Страницы: 68

Бренд: QDI Страницы: 47

Бренд: JETWAY Страницы: 46

Бренд: Gigabyte Страницы: 96

Бренд: AOpen Страницы: 125

Бренд: Supermicro Страницы: 121

MVME61006E-0161

Бренд: Emerson Страницы: 100

MVME6100 Series

Бренд: Emerson Страницы: 118

Бренд: Emerson Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды