Yamaha V150D Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 81

background image

Trouble Recovery

66

unless the oil level warning indicators

are working.

1.

Remove the top cowling.

2.

Turn on the main switch.

3.

Lift the emergency switch to pump re-
serve oil into the engine oil tank from the
remote oil tank.

4.

After using the emergency switch, turn
off the main switch, then turn it back on.
This resets the warning system to nor-
mal operation. The yellow segment will
continue to be displayed on the oil level
indicator.

5.

Start the engine and return to the near-
est port for more oil.

NOTE:

●

The maximum reserve oil capacity is 1500
cm

3

(1.6 US qt, 1.31 Imp qt).

●

The oil-feed pump will not operate if the
engine is tilted up more than 35°. Put the
engine in the upright position (not tilted)

before using the emergency switch.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.

EMU29771

Procedure

1.

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

1. Emergency switch

1. Engine oil tank

OFF

ON

ZMU01880

1

ZMU03925

1

2

ZMU01908

2. Remote oil tank

ZMU01909

«
...
69
70
71
72
73
...
»

Содержание V150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для V150D

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 76

JW-A880GM-FUSION

Бренд: J&W Страницы: 38

SuperServer SYS-E102-9AP-LN4-C

Бренд: Supermicro Страницы: 81

Бренд: ST Страницы: 22

Бренд: Xilinx Страницы: 31

Бренд: JETWAY Страницы: 37

Бренд: Freetech Страницы: 48

Бренд: DAQ system Страницы: 52

Бренд: ISSC Страницы: 39

Бренд: Gigabyte Страницы: 81

Бренд: ASROCK Страницы: 18

Бренд: Humandata Страницы: 10

Бренд: ASROCK Страницы: 26

Бренд: Linear Страницы: 16

Бренд: ASROCK Страницы: 144

Бренд: TYAN Страницы: 164

DisplayPort VIP Input Board

Бренд: Lattice Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды