Yamaha V150D Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 81

background image

Trouble Recovery

65

EMU29670

Engine fails to operate

EMU29691

Ignition system malfunction

If the battery voltage is low or in the unlikely
event of an ignition system malfunction, the
engine speed may become erratic or the en-
gine may stop. In such a situation, follow the
procedure below.
1.

Remove the CDI unit cover or electrical
cover, if equipped.

2.

Disconnect the yellow cord (emergency
circuit) of the CDI unit to return to port.

WARNING

EWM00350

When the yellow cord is disconnected,
the idle and low speeds are slightly high-
er than normal. Use care when starting off

or stopping.

CAUTION:

ECM00380

Follow this procedure only in an emer-
gency and just long enough to return to

port for repairs.

EMU29740

Low oil level warning activates

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator, the buzzer will sound, and engine
speed will be limited to about 2000 r/min. If
this happens, a reserve amount of oil can be
pumped from the remote oil tank to the en-
gine oil tank using the emergency switch.

WARNING

EWM01050

Be sure to stop the engine before per-

forming this procedure.

CAUTION:

ECM00900

●

If the emergency switch is held up too
long, too much oil will be pumped into
the engine oil tank, overflowing it. Re-
lease the switch when oil reaches the
upper level line on the engine oil tank.

●

Do not use this emergency procedure

ZMU03466

ZMU03923

1. CDI unit
2. Yellow cord

1

2

ZMU03924

«
...
68
69
70
71
72
...
»

Содержание V150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для V150D

Бренд: IEI Technology Страницы: 155

Бренд: IEI Technology Страницы: 281

Бренд: IEI Technology Страницы: 151

Бренд: IEI Technology Страницы: 169

Бренд: IEI Technology Страницы: 125

Бренд: IEI Technology Страницы: 165

Бренд: IDT Страницы: 9

Бренд: IEI Technology Страницы: 12

KT333 DRAGON Plus

Бренд: SOYO Страницы: 34

Бренд: Avalue Technology Страницы: 12

Бренд: MIPS Страницы: 10

Бренд: ASROCK Страницы: 128

JW-A880GM-FUSION

Бренд: J&W Страницы: 38

Бренд: J&W Страницы: 40

Бренд: Abit Страницы: 48

Бренд: Quick Страницы: 32

Бренд: JETWAY Страницы: 38

Бренд: R&S Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды