Yamaha V150D Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 81

background image

Maintenance

52

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29130

Water leakage

Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29153

Checking power trim and tilt system

WARNING

EWM00430

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
is locked. Severe injury could occur if
the outboard motor accidentally falls.

●

Make sure no one is under the outboard

motor before performing this test.

1.

Check the power trim and tilt unit for any
sign of oil leaks.

2.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling (if equipped) to
check that all switches work.

3.

Tilt the outboard motor up and check
that the tilt rod and trim rods are extend-
ed completely.

4.

Use the tilt support lever to lock the mo-
tor in the up position. Operate the tilt
down switch briefly so the motor is sup-
ported by the tilt support lever.

5.

Check that the tilt rod and trim rods are
free of corrosion or other flaws.

6.

Activate the tilt-down switch until the trim
rods have retracted completely into the
cylinders.

ZMU03915

1. Tilt rod
2. Trim rods

1. Tilt support lever

ZMU03458

1

2

ZMU03459

1

«
...
55
56
57
58
59
...
»

Содержание V150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для V150D

Бренд: Biostar Страницы: 54

Бренд: QDI Страницы: 85

Бренд: DFI Страницы: 67

Бренд: ST Страницы: 13

Бренд: Xilinx Страницы: 56

Бренд: PCchips Страницы: 42

Бренд: VIA Technologies Страницы: 86

P35D3 Platinum - Motherboard - ATX

Бренд: MSI Страницы: 104

Бренд: VIA Technologies Страницы: 81

Бренд: Ublox Страницы: 22

Бренд: Aeroflex Страницы: 32

Бренд: ASROCK Страницы: 98

Бренд: unicore Страницы: 29

Бренд: unicore Страницы: 28

lanparty dk P45 series

Бренд: DFI Страницы: 112

BOXD945GCLL - Socket 775 MicroATX Motherboard

Бренд: Intel Страницы: 90

Worcester TDS 300

Бренд: Bosch Страницы: 84

Бренд: Bosch Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды