Yamaha V150D Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 81

background image

Maintenance

51

4.

Reinstall the filter element in the cup.
Make sure the O-ring is in position in the
cup. Firmly screw the cup onto the filter
housing.

5.

Attach the filter assembly to the bracket
so that the fuel hoses are attached to the
filter assembly.

6.

Run the engine and check the filter and
lines for leaks.

EMU29040

Inspecting idling speed

WARNING

EWM00450

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair, and clothes away
from the flywheel and other rotating
parts while the engine is running.

●

2-hp models: The propeller rotates
whenever the engine is running. Do not
move the throttle control lever from the
start position during warm-up. The boat
could unexpectedly start to move,

which could result in an accident.

CAUTION:

ECM00490

This procedure must be performed while
the outboard motor is in the water. A
flushing attachment or test tank can be

used.

A diagnostic tachometer should be used for
this procedure. Results may vary depending
on whether testing is conducted with the
flushing attachment, in a test tank, or with the
outboard motor in the water.
1.

Start the engine and allow it to warm up
fully in neutral until it is running smooth-
ly.
2-hp model: Warm the engine with the
throttle in the start position or less. If the
outboard is mounted on a boat, be sure

the boat is tightly moored.

NOTE:

Correct idling speed inspection is only possi-
ble if the engine is fully warmed up. If not
warmed up fully, the idle speed will measure
higher than normal. If you have difficulty ver-
ifying the idle speed, or the idle speed re-
quires adjustment, consult a Yamaha dealer

or other qualified mechanic.

2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 40.

EMU29050

Checking water in engine oil tank

Oil injection models

There is a water trap at the bottom of the en-
gine oil tank. If water or foreign matter is vis-
ible in this trap, consult your Yamaha dealer.

EMU29111

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

1. Water trap
2. Engine oil tank

2

1

ZMU01895

«
...
54
55
56
57
58
...
»

Содержание V150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для V150D

Бренд: IEI Technology Страницы: 177

Pentium P5I430TX/IIB TITANIUM IIB

Бренд: QDI Страницы: 53

CVN X570 GAMING PRO V14

Бренд: Colorful Страницы: 64

PCM-8152 3rd Generation

Бренд: Aaeon Страницы: 6

conga-HPC/EVAL-Server

Бренд: Congatec Страницы: 54

GeForce 8300 (MI-A78U-8309)

Бренд: XFX Страницы: 26

Бренд: JETWAY Страницы: 52

Cypress MB39C502-EVBSK-01

Бренд: Infineon Technologies Страницы: 28

Бренд: Supero Страницы: 90

790XT-G35 series

Бренд: MSI Страницы: 103

A320M-K PRO V14

Бренд: Colorful Страницы: 12

Бренд: Advantech Страницы: 82

Бренд: Commell Страницы: 53

Бренд: Texas Instruments Страницы: 20

THUNDER I7501 XTREME

Бренд: TYAN Страницы: 48

Бренд: Kontron Страницы: 105

Бренд: ECS Страницы: 60

Бренд: Gigabyte Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды