Yamaha T8C Скачать руководство пользователя страница 112

Страница: 112 / 129

5-3

E. Engine power loss.

1. Propeller damaged.

1. Have propeller repaired or replaced.

2. Propeller pitch or diameter incorrect.

2. Install correct propeller to operate out-

board at its recommended speed
(r/min) range.

3. Trim angle incorrect.

3. Adjust trim angle to achieve most effi-

cient operation.

4. Motor mounted at incorrect height on

transom.

4. Have motor adjusted to proper transom

height.

5. Warning system activated.

5. Find and correct cause of warning.

6. Boat bottom fouled with marine growth.

6. Clean boat bottom.

7. Spark plug(s) fouled or incorrect type.

7. Inspect spark plug(s). Clean or replace

with recommended type.

8. Weeds or other foreign matter tangled

on gear housing.

8. Remove foreign matter and clean lower

unit.

9. Fuel system obstructed.

9. Check for pinched or kinked fuel line or

other obstructions in fuel system.

10. Fuel filter clogged.

10. Clean or replace filter.

11. Fuel contaminated or stale.

11. Fill tank with clean, fresh fuel.

12. Spark plug gap incorrect.

12. Inspect and adjust as specified.

13. Poor connections or damaged ignition

wiring.

13. Check wires for wear or breaks.

Tighten all loose connections.
Replace worn or broken wires.

14. Failed ignition parts.

14. Have serviced by a Yamaha dealer.

15. Specified engine oil not used.

15. Check and replace oil with specified

type.

16. Thermostat faulty or clogged.

16. Have serviced by a Yamaha dealer.

17. Air vent screw closed.

17. Open the air vent screw.

18. Fuel pump damaged.

18. Have serviced by a Yamaha dealer.

19. Fuel joint connection incorrect.

19. Connect correctly.

20. Heat range of spark plug incorrect.

20. Inspect spark plug and replace it with

recommended type.

21. Engine not responding properly to shift

lever position.

21. Have serviced by a Yamaha dealer.

F. Engine vibrates

excessively.

1. Propeller damaged.

1. Have propeller repaired or replaced.

2. Propeller shaft damaged.

2. Have serviced by a Yamaha dealer.

3. Weeds or other foreign matter tangled

on propeller.

3. Remove and clean propeller.

4. Motor mounting bolt loose.

4. Tighten bolt.

5. Clamp screw is loose.

5. Tighten the clamp screw.

6. Steering pivot loose or damaged.

6. Tighten or have serviced by a Yamaha

dealer.

Trouble

Possible Cause

Remedy

Содержание T8C


































































































































Результаты поиска

Содержание T8C

Отзывы:

Похожие инструкции для T8C

Бренды по названию

Популярные бренды

Yamaha T8C, Руководство пользователя

Результаты поиска

Содержание T8C

Отзывы:

Похожие инструкции для T8C

Бренды по названию

Популярные бренды