Yamaha T8C Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 129

background image

2-10

E

EMU00100

Neutral Throttle Lever

To open the throttle without shifting into
either Forward or Reverse, place the remote
control lever in the Neutral position and lift
the neutral throttle lever.

NOTE:

@

The neutral throttle lever will operate only
when the remote control lever is in Neutral.
The remote control lever will operate only
when the neutral throttle lever is in the
closed position.

@

1

Fully open

2

Fully closed

EMU00101

Main switch

The main switch controls the ignition sys-
tem; its operation is described below.

●

OFF

Electrical circuits switched off.
(The key can be removed.)

●

ON

Electrical circuits switched on.
(The key cannot be removed.)

●

START

Starter-motor will turn and start engine.
(When the key is released, it returns auto-
matically to “ON”.)

«
...
31
32
33
34
35
...
»

Содержание T8C


































































































































Отзывы:

Нет отзывов

Похожие инструкции для T8C

Бренд: Ublox Страницы: 23

Бренд: Gigabyte Страницы: 93

Бренд: MediaQ Страницы: 25

Бренд: Xilinx Страницы: 70

Бренд: Alpha Data Страницы: 40

Бренд: Unicorn Computer Страницы: 36

Бренд: JETWAY Страницы: 19

Бренд: ECS Страницы: 61

Бренд: Supermicro Страницы: 97

Бренд: Biostar Страницы: 68

Бренд: Texas Instruments Страницы: 21

Бренд: JETWAY Страницы: 50

Бренд: Linear Technology Страницы: 8

Бренд: Watersnake Страницы: 24

Бренд: Consumer Microcircuits Страницы: 58

GA-Z170X-Ultra Gaming

Бренд: Gigabyte Страницы: 48

Бренд: Gigabyte Страницы: 100

Бренд: Gigabyte Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды