Yamaha T8C Скачать руководство пользователя страница 96

Страница: 96 / 129

4-21

EMU01322

CHECKING POWER TILT SYSTEM

WARNING

●

Never get under the lower unit while it
is tilted, even when the tilt-support
knob is locked. Severe injury could
occur if the outboard accidentally falls.

●

Make sure no one is under the out-
board before performing this test.

1) Check the power tilt unit for any sign of

oil leaks.

2) Operate each of the power tilt switches

on remote control and engine bottom
cowling (if equipped) to check that all
switches work.

3) Tilt up the motor and check that the tilt

rod

is pushed out completely.

4) Check that the tilt rod is free of corrosion

or other flaws.

5) Operate the motor to tilt down. Check

that the tilt rod operates smoothly.

NOTE:

If any operation is abnormal, consult a
Yamaha dealer.

Recommended fluid;
Yamaha power trim & tilt fluid or ATF
(DEXRON-

)

Содержание T8C


































































































































Результаты поиска

Содержание T8C

Отзывы:

Похожие инструкции для T8C

Бренды по названию

Популярные бренды

Yamaha T8C, Руководство пользователя

Результаты поиска

Содержание T8C

Отзывы:

Похожие инструкции для T8C

Бренды по названию

Популярные бренды