Yamaha T8C Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 129

background image

3-24

E

EMU00285

TILTING UP/DOWN

If the engine will be stopped for some time,
or if the boat is moored in shallows, the
engine should be tilted up to protect the pro-
peller and casing from damage by collision
with obstructions, and also to reduce salt
corrosion.

CAUTION:

@

●

Before tilting the motor, follow the pro-
cedures under “STOPPING ENGINE”.
Never tilt the motor while the engine is
running. Severe damage from over-
heating can result.

●

Do not tilt up the engine by pushing
the steering handle as this could break
the handle.

@

WARNING

@

Be sure all people are clear of the out-
board motor when adjusting the tilt
angle, also be careful not to pinch any
body parts between the drive unit and
engine bracket.

@

WARNING

@

Leaking fuel is a fire hazard. Disconnect
the fuel line if the engine will be tilted for
more than a few minutes. Otherwise, fuel
may leak. (If the fuel connector is pro-
vided on the motor.)

@

«
...
63
64
65
66
67
...
»

Содержание T8C


































































































































Отзывы:

Нет отзывов

Похожие инструкции для T8C

Бренд: SOLTEK Страницы: 49

Бренд: Atmel Страницы: 22

Бренд: Portwell Страницы: 7

KEEX-1850 Series

Бренд: Quanmax Страницы: 61

Бренд: Gigabyte Страницы: 104

Бренд: Supero Страницы: 80

Бренд: Aaeon Страницы: 108

Бренд: COX Страницы: 60

Бренд: TYAN Страницы: 130

Бренд: Intel Страницы: 91

Бренд: ST Страницы: 52

Бренд: unicore Страницы: 11

Бренд: AMD Страницы: 36

Бренд: ASROCK Страницы: 57

Бренд: DFI Страницы: 92

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 26

Бренд: Siemens Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды