Yamaha T8C Скачать руководство пользователя страница 105

Страница: 105 / 129

4-30

EMU01279¯

Connecting the Battery

WARNING

Mount the battery holder securely in a
dry, well-ventilated, vibration-free loca-
tion in the boat. Install a fully charged
battery in the holder.

CAUTION:

●

Make sure the main switch (on applica-
ble models) is “OFF” before working
on the battery.

●

Reversal of the battery leads will dam-
age the rectifier.

●

Connect the RED lead first when
installing the battery and disconnect
the RED lead last when removing it.
Otherwise, the electrical system can
be damaged.

●

The electrical contacts of the battery
and cables must be clean and properly
connected, or the battery will not start
the engine.

Connect the RED lead to the POSITIVE (+)
terminal first.
Then connect the BLACK lead to the NEGA-
TIVE (-) terminal.

Red lead

Black lead

Battery

EMU01280

Disconnecting the Battery

Disconnect the BLACK lead from the NEGA-
TIVE (-) terminal first. Then disconnect the
RED lead from the POSITIVE (+) terminal.

Содержание T8C


































































































































Результаты поиска

Содержание T8C

Отзывы:

Похожие инструкции для T8C

Бренды по названию

Популярные бренды

Yamaha T8C, Руководство пользователя

Результаты поиска

Содержание T8C

Отзывы:

Похожие инструкции для T8C

Бренды по названию

Популярные бренды