Yamaha T8C Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 129

background image

4-6

E

EMU00335

Filling Fuel Tank

Fill the fuel tank with fresh fuel and add one
ounce of “Yamaha Fuel Conditioner and Sta-
bilizer” (Part No. LUB-FUELC-12-00) to
each gallon of fuel.

NOTE:

@

The use of “Yamaha Fuel Conditioner and
Stabilizer” eliminates the need to drain the
fuel system. Consult your Yamaha dealer or
other qualified mechanic if the fuel system is
to be drained instead.

@

EMU00338

Flushing Cooling System and Fogging
Engine

Cooling system flushing is essential to pre-
vent the cooling system from clogging up
with salt, sand, or dirt. In addition, fogging of
the engine is mandatory to prevent expen-
sive engine damage due to rust. Perform the
flushing and fogging at the same time.

WARNING

@

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair and clothes away
from flywheel and other rotating parts
while engine is running.

@

«
...
79
80
81
82
83
...
»

Содержание T8C


































































































































Отзывы:

Нет отзывов

Похожие инструкции для T8C

Бренд: A-Trend Страницы: 40

Бренд: Texas Instruments Страницы: 52

JW-A880GM-FUSION

Бренд: J&W Страницы: 38

Бренд: TYAN Страницы: 67

Бренд: Biostar Страницы: 43

Бренд: JETWAY Страницы: 46

Бренд: Avalue Technology Страницы: 82

B550 AORUS ELITE AX V2

Бренд: Gigabyte Страницы: 12

Бренд: Telaire Страницы: 4

Бренд: CHAINTECH Страницы: 59

Бренд: DFI Страницы: 130

P55 GD80 - Motherboard - ATX

Бренд: MSI Страницы: 150

Бренд: JETWAY Страницы: 57

Бренд: Gigabyte Страницы: 44

Бренд: Seanix Страницы: 49

Бренд: ITX SECURITY Страницы: 18

Бренд: ALi Confidential Страницы: 24

Бренд: Micronics Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды