Yamaha T8C Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 129

background image

4-17

E

EMU09912

INSPECTING IDLING SPEED

WARNING

@

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair and clothes away
from flywheel and other rotating parts
while engine is running.

@

CAUTION:

@

This procedure must be performed while
the outboard motor is in the water. A
flushing attachment or test tank can also
be used.

@

A diagnostic tachometer should be used for
this procedure. Results may vary depending
on whether testing is conducted with the
flushing attachment, in a test tank, or with
the outboard motor in the water.
1) Start the engine and allow it to warm up

fully in neutral until it is running
smoothly. If the outboard motor is
mounted on a boat, be sure the boat is
tightly moored.

2) Verify whether the idle speed is set to

specification. For idle speed specifica-
tions, see “Specifications” in this chap-
ter.

NOTE:

@

Correct idling speed inspection is only pos-
sible if the engine is fully warmed up. If not
warmed up fully, the idle speed will measure
higher than normal. If you have difficulty ver-
ifying the idle speed, or the idle speed
requires adjustment, consult a Yamaha
dealer or other qualified mechanic.

@

«
...
90
91
92
93
94
...
»

Содержание T8C


































































































































Отзывы:

Нет отзывов

Похожие инструкции для T8C

DCDC SBC Series

Бренд: Infineon Страницы: 17

Бренд: Mercury Страницы: 41

Бренд: JETWAY Страницы: 49

SKR E3 DIP V1.0

Бренд: BIGTREETECH Страницы: 10

B560M DS3H PLUS

Бренд: Gigabyte Страницы: 42

Бренд: DFI Страницы: 120

Бренд: Gigabyte Страницы: 18

Бренд: Acorp Страницы: 74

Бренд: Microchip Technology Страницы: 34

ISL70321SEHDEMO1Z

Бренд: Intersil Страницы: 9

Бренд: Intel Страницы: 92

Бренд: DFI Страницы: 150

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

Бренд: Ublox Страницы: 22

CAES UT65CML8X8FD-EVB-UM

Бренд: COBHAM Страницы: 20

Бренд: IEI Technology Страницы: 53

Бренд: ST Страницы: 52

Бренд: DFI Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды