Yamaha LZ300C Скачать руководство пользователя страница 49

Страница: 49 / 84

Operation

ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28182

Procedure for power trim and tilt/power
tilt models

Place the gear shift lever in neutral.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28190

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with
salt deposits.

NOTE:

For cooling system flushing instructions, see

page 46.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
if you use the outboard motor in turbid (mud-
dy) water conditions.

ZMU01935

ZMU01888

ZMU01954

Содержание LZ300C





















































































Результаты поиска

Содержание LZ300C

Отзывы:

Похожие инструкции для LZ300C

Бренды по названию

Популярные бренды

Yamaha LZ300C, Руководство пользователя

Результаты поиска

Содержание LZ300C

Отзывы:

Похожие инструкции для LZ300C

Бренды по названию

Популярные бренды