Yamaha LZ300C Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 84

background image

Maintenance

57

or other qualified mechanic.

2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 45.

EMU29050

Checking water in engine oil tank

Oil injection models

There is a water trap at the bottom of the en-
gine oil tank. If water or foreign matter is vis-
ible in this trap, consult your Yamaha dealer.

EMU29110

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29130

Water leakage

Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29150

Checking power trim and tilt system

WARNING

EWM00430

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
is locked. Severe injury could occur if
the outboard motor accidentally falls.

●

Make sure no one is under the outboard

motor before performing this test.

1.

Check the power trim and tilt unit for any
sign of oil leaks.

2.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling (if equipped) to
check that all switches work.

3.

Tilt the outboard motor up and check
that the tilt rod and trim rods are extend-
ed completely.

4.

Use the tilt support lever to lock the mo-
tor in the up position. Operate the tilt
down switch briefly so the motor is sup-
ported by the tilt support lever.

5.

Check that the tilt rod and trim rods are
free of corrosion or other flaws.

6.

Activate the tilt-down switch until the trim
rods have retracted completely into the

1. Water trap
2. Engine oil tank

2

1

ZMU01895

1. Tilt rod
2. Tilt support lever
3. Trim rods

1

ZMU01940

3

2

«
...
60
61
62
63
64
...
»

Содержание LZ300C





















































































Отзывы:

Нет отзывов

Похожие инструкции для LZ300C

Бренд: QDI Страницы: 69

Бренд: ECS Страницы: 52

Бренд: AOpen Страницы: 8

Pentium P5I430TX/IIB TITANIUM IIB

Бренд: QDI Страницы: 53

CVN X570 GAMING PRO V14

Бренд: Colorful Страницы: 64

Бренд: JETWAY Страницы: 47

SKR E3 DIP V1.0

Бренд: BIGTREETECH Страницы: 10

B560M DS3H PLUS

Бренд: Gigabyte Страницы: 42

NORA-W10 Series

Бренд: Ublox Страницы: 22

Бренд: ASROCK Страницы: 154

Z690M DS3H DDR4

Бренд: Gigabyte Страницы: 36

Бренд: XFX Страницы: 120

Бренд: ASROCK Страницы: 160

Бренд: Erreka Страницы: 4

Бренд: Avalue Technology Страницы: 80

Бренд: AOpen Страницы: 11

Бренд: COX Страницы: 60

Бренд: Raisonance Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды