Yamaha LZ300C Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 84

background image

Operation

40

bottom engine cowling (if equipped)
only when the boat is at a complete

stop with the engine off.

Adjust the outboard motor trim angle using
the power trim and tilt switch.

To raise the bow (trim-out), press the switch
“

” (up).

To lower the bow (trim-in), press the switch
“

” (down).

Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.

NOTE:

To adjust the trim angle while the boat is
moving, use the power trim and tilt switch lo-
cated on the remote control device or tiller

handle, if equipped.

EMU27910

Adjusting boat trim

When the boat is on plane, a bow-up attitude
results in less drag, greater stability and effi-
ciency. This is generally when the keel line of
the boat is up about 3 to 5 degrees. With the
bow up, the boat may have a greater tenden-
cy to steer to one side or the other. Compen-
sate for this as you steer. The trim tab can
also be adjusted to help offset this effect.
When the bow of the boat is down, it is easier
to accelerate from a standing start onto
plane.

Bow Up

Too much trim-out puts the bow of the boat
too high in the water. Performance and econ-
omy are decreased because the hull of the

1. Power trim and tilt switch

1. Power trim and tilt switch

1. Power trim and tilt switch

UP

DN

ZMU01944

1

1. Optimum angle (level keel line)

«
...
43
44
45
46
47
...
»

Содержание LZ300C





















































































Отзывы:

Нет отзывов

Похожие инструкции для LZ300C

Бренд: P&E Microcomputer Systems Страницы: 59

Бренд: Xilinx Страницы: 14

Бренд: Ublox Страницы: 23

Бренд: Acrosser Technology Страницы: 7

Бренд: Gigabyte Страницы: 100

Бренд: Microchip Technology Страницы: 52

Бренд: Texas Instruments Страницы: 16

Бренд: Ublox Страницы: 18

TB360-BTC PRO 2.0

Бренд: Biostar Страницы: 59

Бренд: Evinrude Страницы: 76

Бренд: Aaeon Страницы: 119

Бренд: Telit Wireless Solutions Страницы: 47

ISL9122AIIN-EVZ

Бренд: Renesas Страницы: 17

Бренд: ON Semiconductor Страницы: 5

Бренд: Fastrax Страницы: 12

Бренд: Gigabyte Страницы: 96

Бренд: JETWAY Страницы: 55

Бренд: J&W Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды