Yamaha LZ300C Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 84

background image

Basic components

17

EMU26150

Power trim and tilt switch on bottom
engine cowling

The power trim and tilt switch is located on
the side of the bottom engine cowling. Press-
ing the switch “

” (up) trims the outboard

motor up, then tilts it up. Pressing the switch
“

” (down) tilts the outboard motor down

and trims it down. When the switch is re-
leased, the outboard motor will stop in its
current position.

WARNING

EWM01030

Use the power trim and tilt switch located
on the bottom engine cowling only when
the boat is at a complete stop with the en-
gine off. Attempting to use this switch
while the boat is moving could increase
the risk of falling overboard and could
distract the operator, increasing the risk
of collision with another boat or an obsta-

cle.

NOTE:

For instructions on using the power trim and

tilt switch, see page 41.

EMU26161

Power trim and tilt switches (twin
binnacle type)

The power trim and tilt system adjusts the
outboard motor angle in relation to the tran-
som. Pushing the switch “

” (up) trims the

outboard motor up, then tilts it up. Pressing
the switch “

” (down) tilts the outboard mo-

tor down and trims it down. When the switch
is released, the outboard motor will stop in its
current position.

NOTE:

●

On the dual engine control, the switch on
the remote control grip controls both out-
board motors at the same time.

●

For instructions on using the power trim

and tilt switches, see pages 39 and 41.

UP

DN

ZMU01862

«
...
20
21
22
23
24
...
»

Содержание LZ300C





















































































Отзывы:

Нет отзывов

Похожие инструкции для LZ300C

EZ-USB HX2LP CY4605

Бренд: Cypress Страницы: 2

Бренд: Gigabyte Страницы: 93

Бренд: JETWAY Страницы: 56

Бренд: Biostar Страницы: 71

Бренд: ECS Страницы: 60

Бренд: Arbor Technology Страницы: 86

Бренд: CHAINTECH Страницы: 59

SERVER SYSTEM SR2500AL

Бренд: Intel Страницы: 210

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренд: ECS Страницы: 92

EVAL-IH-R5IPB-A-V1

Бренд: Infineon Страницы: 34

Бренд: Commell Страницы: 53

Бренд: Texas Instruments Страницы: 20

Бренд: Qiyangtech Страницы: 16

Бренд: BESTEK Страницы: 13

Бренд: Linear Technology Страницы: 6

25 Jet FourStroke

Бренд: Mercury Страницы: 110

Бренд: Advantech Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды